HIGHSIDER display 1-sided

The HIGHSIDER license plate holder AKRON-RS adapts perfectly to the lines of your bike through its design.The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.The license plate is made of sheet steel and 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating.This ensures an optimal fit and durability.The stepless adjustment allows you to bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.The turn signal holders of the AKRON-RS are adjustable in width and thus suitable for any type of accessory turn signals. This adjustability allows you to adjust the position for your turn signals to the most different license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side.You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem.To screw the license plate securely and reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside.Details:- model-specific mount- infinitely adjustable turn signal holder- slotted turn signal mount for easy installation without cable separation- infinitely adjustable reflector, E-approved- suitable for European license plates- infinitely adjustable angle of inclination- additional screw for optimal position security- easy fixation without further work steps (e.g. drilling)- easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes- Model-related holder with mounting parts- AKRON-RS license plate holder- Adjustable turn signal brackets- E-tested reflector with adjustable holder- Mounting instructionsNotes:- A special turn signal holder is optionally available for the original turn signals in the accessories tab.- If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.Tips:If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.

Handlebar mirror, adjustable mirror arm in matt black anodised finish. The use of a second joint on the stem provides additional adjustment options.Suitable for both left and right sides, E-approved.Details: Width, head: 120 mmHeight, head: 85 mmDepth: 24 mmLength, arm to joint: 150 mmLength, arm to threaded bolt: 180 mmBlind hole: M8 x 1.25 mmMaterial: aluminiumContents: 1 piece (including an extra M10 x 1.25 mm adapter with left-hand thread, e.g. for Yamaha) Note: For Vespa ET, LX and GTS models, please order one mirror adapter (M8 x 1.25 mm with right-hand thread) per mirror for fitting (item no. 85.304045)

Noble, CNC-milled handlebar end mirror with a round head made of high quality aluminum, anodized black. The stylized propeller on the back of the mirror head underlines the extraordinary design of this model. Thanks to an innovative universal clamping system, the mirrors fit handlebars with an inner handlebar diameter of 12 to 22 mm. The stem is adjustable up and down and offers an even better view to the rear and more safety. Can be used for right and left side.Prudence with style - whether classic or modern. The HIGHSIDER mirror series are characterized by striking design and aerodynamic function. So you keep the overview.DimensionsTotal width: 40 mm (adjustable)Total height: approx. 150 mmDiameter head: 100 mmHandle length: approx. 95 mmCentral screw: M6 x 1.0 mm hexagon socket screwE-tested ✓Scope of delivery: 1 piece incl. mounting set and universal clamping system (for both sides 2x order) Suitable for: Vespa GTS / GTS Super / GTV / GT /GT LDoes not fit: Vespa ET4 / LX / LXV / S / Primavera / Sprint

Noble, CNC-milled handlebar end mirror with a round head made of high-quality aluminum, chrome-plated. The stylized propeller on the back of the mirror head underlines the extraordinary design of this model. Thanks to an innovative universal clamping system, the mirrors fit handlebars with an inner handlebar diameter of 12 to 22 mm. The stem is adjustable up and down and offers an even better view to the rear and more safety. Can be used for right and left side.Prudence with style - whether classic or modern. The HIGHSIDER mirror series are characterized by striking design and aerodynamic function. So you keep the overview.DimensionsTotal width: 40 mm (adjustable)Total height: approx. 150 mmDiameter head: 100 mmHandle length: approx. 95 mmCentral screw: M6 x 1.0 mm hexagon socket screwE-tested ✓Scope of delivery: 1 piece incl. mounting set and universal clamping system (for both sides 2x order) Suitable for: Vespa GTS / GTS Super / GTV / GT /GT LDoes not fit: Vespa ET4 / LX / LXV / S / Primavera / Sprint

Due to the elaborate CNC milled surface, the ENTERPRISE-EP1 looks very futuristic and there are many details reflected in the round shape of the ENTERPRISE-EP1 for the viewer.Handlebar end mirrors give motorcycles a very special look.For those who find NORMAL mirrors simply too unspectacular, the HIGHSIDER handlebar end mirror range has the solution.With short hanging handlebar end mirrors, many a well-behaved bike suddenly gets a slightly aggressive touch.The mirror can be used on the left or right and a joint on the mounting clamp provides individual adjustment options for the driver.Mountable either with the supplied reducing sleeves directly on the steering tube or on optionally available handlebar ends with handlebar end mirror mount.With the highest level of quality and functionality, you can easily customize your bike to your liking with accessories from HIGHSIDER.A question of vision - whether retro or modern. The HIGHSIDER mirror series are characterized by characteristic design and aerodynamic function. So you can keep an overview.- Can be used for left and right side - Scope of delivery: 1 piece (for left and right 2 x order)- E-approved ✓Mounting info for Vespa GTS / GTS Super / GTV / GT /GT L:  To mount the handlebar end mirrors, you need the adapter 165LVV02 or if you want to use the mirrors with the original handle bar ends the adapter 85.476010Mounting information for Vespa ET4 / LX / LXV / S / Primavera / Sprint:  For mounting you need a handle with "handlebar end opening" or you have to cut the original one. For mounting you need the adapter: 165-LV4SW Dimensions:A Width head: 100 mmB Height head: 100 mmC Width: 60-120 mmD Height: 150 mmStem length approx: 80 mmOutside diameter of the clamp 35 mmInner diameter: 29.9 mm

Handlebar end mirrors for your VespaCharacter and overview - whether retro or modern. The Handlebar end mirrors for your Vespa are characterized by their design and aerodynamic function. This is circumspection in perfection.- Noble design, with a round head made of black shiny Aluminum. - For left and right side usable - Scope of delivery: 1 piece (for left and right 2 x order)- E-approved ✓Mounting info for Vespa GTS / GTS Super / GTV / GT /GT L:  To mount the handlebar end mirrors, you need the adapter 165LVV02 or if you want to use the mirrors with the original handle bar ends the adapter 85.476010Mounting information for Vespa ET4 / LX / LXV / S / Primavera / Sprint:  For mounting you need a handle with "handlebar end opening" or you have to cut the original one. For mounting you need the adapter: 165-LV4SW Dimensions:Diameter: 102 mmStem length to bend: 70 mmStem length to clamp end: 115 mm

The characteristic stealth design known from the military stealth technology distinguishes the shapely and high-quality crafted mirror. Combined with the color matte black, the mirror head made of high-quality plastic with its angular elements has a striking appearance. Further visual accents can be found in the short mirror arm made of aluminum, which is equipped with three sporty air slits and offers additional adjustment options for a better view thanks to a joint on the clamp. Thanks to the use of lightweight materials, the STEALTH series from HIGHSIDER belongs to the weight class of flyweights. An adjustable joint provides additional adjustment possibilities of the STEALTH -X5.The mirror can be used on the left and right. Mountable either with the supplied reducing sleeves directly on the steering tube or on optionally available handlebar ends with handlebar end mirror mount. (see accessories)Scope of delivery: 1 piece incl.- 1 X adapter 1 inch- 1 X adapter 7/8 inch- For left and right side usable - Scope of delivery: 1 piece (for left and right 2 x order)- E-approved ✓Mounting info for Vespa GTS / GTS Super / GTV / GT /GT L:  To mount the handlebar end mirrors, you need the adapter 165LVV02 or if you want to use the mirrors with the original handle bar ends the adapter 85.476010Mounting information for Vespa ET4 / LX / LXV / S / Primavera / Sprint:  For mounting you need a handle with "handlebar end opening" or you have to cut the original one. For mounting you need the adapter: 165-LV4SW Dimensions:A Width head: 119 mmB Height head: 90 mmC Total width: 125 mmD Total height: 150 mmHandle length: 75 mmWeight: 130 g

Handlebar end mirrors for your VespaCharacter and overview - whether retro or modern. The Handlebar end mirrors for your Vespa are characterized by their design and aerodynamic function. This is circumspection in perfection.- Noble design, with a round head made of black shiny Aluminum. - For left and right side usable - Scope of delivery: 1 piece (for left and right 2 x order)- E-approved ✓Mounting info for Vespa GTS / GTS Super / GTV / GT /GT L:  To mount the handlebar end mirrors, you need the adapter 165LVV02 or if you want to use the mirrors with the original handle bar ends the adapter 85.476010Mounting information for Vespa ET4 / LX / LXV / S / Primavera / Sprint:  For mounting you need a handle with "handlebar end opening" or you have to cut the original one. For mounting you need the adapter: 165-LV4SW Dimensions:A: Width, head: 117 mmB: Height, head: 83 mmC: Width: 210 mmStem length center-center: 120 mmOutside diameter of the clamp: 37 mmHint: Tightening torque of M5 screw: 5-7 Nm

Handlebar end mirrors for your VespaCharacter and overview - whether retro or modern. The Handlebar end mirrors for your Vespa are characterized by their design and aerodynamic function. This is circumspection in perfection.- Noble design, with a round head made of chrome-plated Aluminum. - For left and right side usable - Scope of delivery: 1 piece (for left and right 2 x order)- E-approved ✓Mounting info for Vespa GTS / GTS Super / GTV / GT /GT L:  To mount the handlebar end mirrors, you need the adapter 165LVV02 or if you want to use the mirrors with the original bar ends the adapter 85.476010Mounting info for Vespa ET4 / LX / LXV / S / Primavera / Sprint:  For mounting you need a handle with "handlebar end opening" or you have to cut the original one. For mounting you need the adapter: 165-LV4SW Dimensions:Diameter: 102 mmStem length to bend: 70 mmStem length to clamp end: 115 mm

Rubber nuts Thread: M5 Outer diameter: 9.5 mm Flat head screws with hexagon socket Diameter of half-round head: approx. 10 mm Supplied with 8 transparent plastic washers.

Rubber nuts Thread: M6 Outer diameter: 12.5 mm Total height of the nuts: 16 mm Flat head screws with hexagon socket Diameter of half-round head: approx. 16 mm Thread length: 19 mm Supplied with 8 transparent plastic washers.

HIGHSIDER CNC machined aluminum brake fluid reservoir cover, high gloss anodized in black or chrome. Fits Triumph 1200 Thruxton 2016-, Bobber, Boneville T 100/120.Character and style are in the smallest details. Simply replace the classy cover with the original and add another valuable touch to your bike.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can thus easily design your bike according to your wishes.Scope of delivery:1x brake coverNotice:Only suitable for DOT 4.The original screws and seals are used.Caution when replacing the cover. Best to cover the area generously with rags, because brake fluid can attack the paint of the vehicle.