ARROW Auspuff WORKS Titan für Ducati Panigale V2/Streetfighter V2 Modelljahr 2020-2024
ARROW Auspuff WORKS Titan für Ducati Panigale V2/Streetfighter V2 Modelljahr 2020-2024 ARROW WORKS Racing-Endschalldämpfer-Paar (rechts und links), mit Titan-Hülle und Carbon-Endkappe, Für Ducati Panigale V2, Typ 1H, Modelljahr 2020-2024 Streetfighter V2, Typ 3F, Modelljahr 2022-2024 Zur Verwendung mit dem originalen Krümmer Die Fehlermeldung die durch den Entfall der Auspuffklappe entsteht, kann durch den Einbau des Healtech Auspuffklappen Servo Eliminator: AR-AQESED04 verhindert werden (separat bestellen/keine Straßenzulassung)! Produktkennzeichnung: Abgastechnik ARROW Hinweis: Zur Verwendung mit dem originalen Krümmer. Die Fehlermeldung die durch den Entfall der Auspuffklappe entsteht, kann durch den Einbau des Healtech Auspuffklappen Servo Eliminator: AR-AQESED04 verhindert werden (separat bestellen/keine Straßenzulassung)! Geänderte Fahrzeugteile: Auspuffklappe entfällt Produkt Typ: ARROW WORKS Ducati Panigale V2 20- Titan
Electrosport controller
The alternator stators and regulators from Electrosport enable reliable replacement of the standard component.
Factory Links Race Series wheel bearing set
FACTORY LINKS bearings are packed with a heavy-duty premium marine grease and an additive of a special complex thickener that allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep out any moisture, we've gone from a 30% grease fill to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specifically designed for on and off-road use, unlike industrial 2RS ball bearings which offer low torque resistance and therefore low resistance to water ingress.
Factory Links steering head bearing kit
Our premium kits contain all the elements required for a complete OEM quality service for your handlebar stem. Our special off-road design of tapered ball bearings and dust balls are specially manufactured to meet stringent OEM quality requirements in terms of materials, dimensional tolerances, hardness and surface roughness. Our kits restore your bicycle handlebar stem to the condition defined by the manufacturer.
Factory Links wheel bearing set
FACTORY LINKS bearings are packed with a heavy duty premium marine grease and an addition of a special complex thickeners which allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep any moisture out, we have gone from 30% grease filling to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specially developed for an Off-Road use, unlike Industrial 2RS type ball bearings offer low torque resistance and hence weak resistance to water intrusion.
HIGHSIDER pro license plate holder Akron-RS Pro With rear light
HIGHSIDER AKRON-RS PRO license plate holder incl. license plate lightThe design of the HIGHSIDER AKRON-RS PRO license plate holder perfectly matches the lines of your bike.The model-specific holder of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus replacement without further drilling or cutting.To prevent damage to cables, all sharp-edged feed-throughs are protected by a rubber membrane grommet.The license plate is made of sheet steel and is 2 mm thick. It is precisely cut to size using a laser. After edging, it is given a weather-resistant black powder coating.This ensures an optimum fit and durability.The stepless adjustment option allows you to position the plate as required without drilling. There is an additional locking screw to hold the plate in this position.The width of the blinker brackets on the HIGHSIDER AKRON-RS PRO can be adjusted, making them suitable for all types of accessory indicators. This adjustment option allows you to adapt the position of your indicators to a wide variety of license plates. The 8 mm holes are slotted to the side to allow the indicators to be fitted without disconnecting them from the wiring harness.You can also individually adjust the position of the rear reflector using a slider. This makes it easy to adapt to the different versions of EU license plates.Two rubber washers are included to securely screw the license plate and reduce vibrations. Another rubber buffer supports the license plate on its underside.This PRO version of the HIGHSIDER AKRON-RS includes the very small HIGHSIDER license plate light milled from high-quality aluminium with mounting plate and support arm. The bracket is adjustable in height and designed to allow mounting in the legally prescribed position.Details:- model-specific bracket- infinitely adjustable blinker holder- slotted blinker holder for simple mounting without cable separation- infinitely adjustable reflector, E-approved- suitable for European license plates- Infinitely adjustable angle of inclination- Additional screw for optimum positional security- Simple fixing without additional work steps (e.g. drilling) - Easy to install without the need for additional toolsE.g. drilling)- easy mounting of the license plate thanks to elongated holes- license plate light incl. holder included in delivery Bracket included in scope of delivery- license plate light, E-approved- infinitely adjustable license plate light- many different options for mounting the license plate lightThe HIGHSIDER AKRON-RS PRO is supplied as standard:- Model-specific bracket with mounting parts- HIGHSIDER AKRON-RS license plate mounting plate- Adjustable blinker brackets- E-approved reflector with adjustable bracket- E-approved license plate light- Installation instructionsNotes:- If side reflectors are fitted to your original license plate holder, these must be refitted in a suitable position or replaced with new ones.- Special blinker holders are optionally available for the original indicators.Tip:If you have not found a model-specific license plate holder for your vehicle, you are sure to find what you are looking for in the universal license plate holders from HIGHSIDER, which are available in many different designs.
HIGHSIDER pro Outdoor Cover Black Moto / Scooter - S (1pc)
HIGHSIDER tarpaulinThe perfect outdoor protection for two-wheelers: High-quality tarpaulin made from elastic, tear-resistant, waterproof and UV-resistant high-tech fiber. With rubberized seams, the hard-wearing motorcycle cover offers the best protection against rain, dew or other moisture. The extremely robust cover has a soft inner fleece and is therefore particularly gentle on the paintwork, even with daily use. Designed for road motorcycles, it meets the highest requirements of two-wheeled riders, not least due to the integrated ventilation openings, heat protection on both sides and reinforced lock eyelet for anti-theft protection. It is attached to the motorcycle with an adjustable click fastener. High-contrast, white HIGHSIDER lettering on the long sides of the black tarpaulin and the white HIGHSIDER logo on the back visually emphasize this premium product. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Determine the correct size of your cover by measuring the length, width and height of your motorcycle/scooter and comparing them with the dimensions given. Dimensions:Size S:Length: 183 cmWidth: 80 cm Height: 115 cmFits most 50 cc scooters.Size M:Length: 203 cmWidth: 80 cm Height: 120 cmFits most light motorcycles (80/125 cc and supersports/superbikes).Size L:Length: 229 cmWidth: 89 cm Height: 125 cmFits most naked bikes.Size XL:Length: 246 cmWidth: 94 cm Height: 130 cmFits most choppers and small touring bikes.Size XXL:Length: 264 cmWidth: 105 cm Height: 135 cmSuitable for large cruisers and touring bikes.Scope of delivery: 1 piece incl. practical carrying bag DETERMINE SIZE:Determine the correct size of your tarpaulin by measuring the length, width and height of your motorcycle/scooter or take the dimensions from the vehicle registration document to compare the specified dimensions. The correct size is a tarpaulin that is about 5-10 cm longer than the length of the motorcycle and about 5 cm above the ground. TIP:Don't buy too big, the more it flaps, the more it rubs. And in winter, a tarpaulin always tears and breaks exactly where it can move around. Make sure there is enough space: a gap of at least five centimetres to the ground increases the chance of air exchange and counteracts condensation. If you are in doubt between two sizes, choose the larger option. NOTE:In the case of STRETCH COVERING tarpaulins, it is recommended to choose a size smaller than normal tarpaulins without stretch properties.
HIGHSIDER pro X-Bar Adventure X04 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Adventure X04 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike Flat XN1 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Black Bead-Shallow, Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Silver Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 handlebars black glossy, aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER smart Type BC 102 Repair clutch lever silver With ABE, adjustable (1pc)
It doesn't always have to be the original. Our HIGHSIDER smart clutch levers replace the original 1 to 1. Precisely manufactured from high-quality aluminum, they meet all requirements. Therefore also with ABE. If you are also looking for the right brake lever, you are sure to find it in our Bikefinder. Note: Not for vehicles equipped with a radar warning system.
Lever set for Ducati models - Barracuda
The Barracuda levers impress with their perfect workmanship and delicate design. The levers are made of high-quality billet aluminum. They can be individually adjusted in 6 stages. There is a joint at the base of the lever to prevent damage or breakage even if it falls over. The levers are supplied exclusively in black anodized and in pairs. Alternatively, the lever end pieces can be reordered and exchanged in different anodized colors (see "Accessories"). The brake and clutch levers are supplied and have an ABE.
Lever set for Ducati models - Barracuda
The Barracuda levers impress with their perfect workmanship and delicate design. The levers are made of high-quality billet aluminum. They can be individually adjusted in 6 stages. There is a joint at the base of the lever to prevent damage or breakage even if it falls over. The levers are supplied exclusively in black anodized and in pairs. Alternatively, the lever end pieces can be reordered and exchanged in different anodized colors (see "Accessories"). The brake and clutch levers are supplied and have an ABE.
LSL Bremshebel Classic R38R, schwarz/rot
LSL Bremshebel Classic R38R, schwarz/rot LSL Bremshebel Classic R38R, schwarz/rot Produktkennzeichnung: LSL Brems- und Kupplungshebel Produkt Typ: LSL Bremshebel Classic R38R, schwarz/rot, lang
