Shad side pannier rack, 3P system, black painted, for Honda CB / CBR 650 R (19-20)
The 3P side mounting system was developed specifically for the SH23, SH35, SH36 and SH38 side cases, as well as the Terra TR30 and TR40 side bags. During the development phase, safety was prioritised above all else, alongside aesthetic considerations. Integrated design: The 3P mounting system adapts perfectly to the contours of the vehicle. The typical right-angled frame has been reduced to a single arm, which supports the three points (3P) required for mounting the panniers. Position: Both the volume of the case and the angle of the 3P system have been designed to shift the weight of the luggage as close as possible to the centre of the motorbike. This ensures greater safety and stability when riding with a full load. Aerodynamics: The use of three mounting points provides both stability and flexibility. This is achieved through a slight oscillation of the pannier. This allows air to circulate freely around the pannier, thereby avoiding the so-called ‘angle effect’ typical of a flat, rigid pannier. Here, too, this results in improved safety and stability whilst riding. Patent pending: The uniqueness and technical innovation of the 3P system have enabled SHAD to patent it. This makes SHAD the sole manufacturer able to offer this mounting system.Main material: SteelNote: Not compatible with SH23, TR27, TR36 and TR47
Short license plate holder LSL incl. license plate light for Honda CB 650 R / CBR 650 R (19-20)
Making good bikes perfect. Following this motto, LSL has developed the license plate holder MANTIS-RS.It fits perfectly to your motorcycle and emphasizes the lines of your bike with its sporty design.And as usual, LSL has thought of everything.The model-specific bracket of the MANTIS-RS allows replacement without further drilling or cutting on the vehicle.The design fits perfectly to the rear of your bike and uses the original mounting points of the vehicle.Sharp-edged feedthroughs are protected with rubber membrane grommets against damage to the cables.The license plate is made of 2 mm thick sheet steel, laser-cut, edged and weather-resistant black powder-coated.The license plate is fixed in the correct position by an additional locking screw.The width-adjustable turn signal holders of the MANTIS-RS are suitable for any type of accessory turn signals. Through this adjustment option, you will find the right position for your turn signals. The adaptation to the most different EU license plates is therefore no problem. The mounting holes of the turn signals have a diameter of 10 mm and are slotted to the side. This makes it possible to mount the turn signals without disconnecting them from the wiring harness.The slider for mounting the rear reflector is also individually adjustable. An adjustment to the different designs of EU license plates is therefore no problem.The two rubber washers supplied are used for vibration-reducing bolting of the license plate. An additional rubber buffer supports the license plate on the underside.Details:- model-specific bracket- infinitely adjustable turn signal holder- slotted turn signal holder for easy mounting without cable separation- infinitely adjustable reflector, E-approved- suitable for European license plates- infinitely adjustable angle of inclination- additional screw for optimal position security- easy fixation without further work steps (e.g. drilling)- easy mounting of the license plate through slotted holesThe scope of delivery of the MANTIS-RS includes:- Model-related holder with mounting parts- MANTIS-RS license plate holder- Adjustable turn signal holders- E-tested reflector with adjustable holder- Mounting instructionsNotes:- A special turn signal holder is optionally available for the original turn signals in the accessories tab.- If side reflectors are mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.Tip:If you haven't found a model-specific license plate holder for your vehicle, you're sure to find what you're looking for in LSL's universal license plate holders, which are available in many different designs.
Short license plate holder incl. license plate light for Honda CB 650 R / CBR 650 R (19-20)
The HIGHSIDER license plate holder AKRON-RS fits through its design perfectly to the lines of your bike.The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.The license plate is made of sheet steel and 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating.This ensures an optimal fit and durability.The stepless adjustment allows you to bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.The turn signal holders of the AKRON-RS are adjustable in width and thus suitable for any type of accessory turn signals. This adjustability allows you to adjust the position for your turn signals to the most different license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side.You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem.To screw the license plate securely and reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside.Details:- model-specific mount- infinitely adjustable turn signal holder- slotted turn signal holder for easy mounting without cable separation- infinitely adjustable reflector, E-approved- suitable for European license plates- infinitely adjustable angle of inclination- additional screw for optimal position security- easy fixation without further work steps (e.g. drilling)- easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes- Model-related holder with mounting parts- AKRON-RS license plate holder- Adjustable turn signal brackets- E-tested reflector with adjustable holder- Mounting instructionsNotes:- A special turn signal holder is optionally available for the original turn signals in the accessories tab.- If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.Tips:If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
LSL brake lever BOW R14 black, short for Honda
LSL lever BOWThe lever is characterized by a previously unattained, lightweight design, which is characterized by large cutouts between the mounting points and the transition to the lever surface. This possibility was created by a newly developed design of the adjustment lock. The adjustment is cleverly carried out by means of a plastic key supplied, which actuates the anodized adjustment star in six different stages without scratching. Thus the adjustment of the lever can be adapted to the needs of the driver completely as desired. In the long version, a slotted hole at the end of the lever in the horizontal direction prevents unintentional application of the lever at high speeds.Special features:- With ABE- Ultra-light lever design (approx. 130g)- 6-fold adjustable- A predetermined breaking point allows the long version to continue driving after a slip and ensures the continued function of the lever- Aerodynamically designed slotted hole at the end of the lever in the long version prevents the application of the lever at high speedsColor: black / black Info about ABE:For this article an ABE and/or parts certificate are available. Please check if your vehicle is registered in the ABE or in the parts certificate and if additional mounting parts (e.g. clamps) are needed (see document). For some models a preliminary required manufacturer's confirmation is available. Downloads: General type approval (ABE)Mounting instructions
LSL brake lever BOW R14 silver, short for Honda
LSL lever BOWThe lever is characterized by a previously unattained, lightweight design, which is characterized by large cutouts between the mounting points and the transition to the lever surface. This possibility was created by a newly developed design of the adjustment lock. The adjustment is cleverly carried out by means of a plastic key supplied, which actuates the anodized adjustment star in six different stages without scratching. Thus the adjustment of the lever can be adapted to the needs of the driver completely as desired. In the long version, a slotted hole at the end of the lever in the horizontal direction prevents unintentional application of the lever at high speeds.Special features:- With ABE- Ultra-light lever design (approx. 130g)- 6-fold adjustable- A predetermined breaking point allows the long version to continue driving after a slip and ensures the continued function of the lever- Aerodynamically designed slotted hole at the end of the lever in the long version prevents the lever from being applied at high speedsColor: silver / silver Info about ABE:For this article an ABE and/or parts certificate are available. Please check if your vehicle is registered in the ABE or in the parts certificate and if additional mounting parts (e.g. clamps) are needed (see document). For some models a preliminary required manufacturer's confirmation is available. Downloads: General type approval (ABE)Mounting instructions
Tankpad / tank protector with CBR logo
Are you tired of your motorcycle paint constantly marked by scratches and abrasion? Then we have the perfect solution for you! The original tank pad / tank protector with CBR logo reliably protects your paint from damage and also looks really cool.The arrow-shaped tank pad in gray is decorated with the CBR logo and gives your motorcycle a sporty look. But not only the design convinces, but also the functionality. The tank pad is made of high-quality material and offers optimum protection against scratches and abrasion by belt buckles, zippers and other objects.The installation of the tank protector is child's play and can be done within a few minutes. Thanks to the self-adhesive back, the pad can be easily applied to the tank and holds there securely and firmly.Honda attaches great importance to quality and durability. Therefore, the tank pad / tank protector with CBR logo is not only robust and durable, but also UV-resistant and weatherproof. So your motorcycle remains protected even in wind and weather and always looks like new.
Original pillion cover Grand Prix Red *R-380* for Honda CBR 650 R BJ 19-
Would you like to give your Honda CBR650R an even sportier look? Then the original Honda seat cover including small comfort cushion is just the thing for you! With this product, you can give your motorcycle a real racing character and stand out from the crowd.The seat cover is specially designed for the 2019 and newer Honda CBR650R and fits perfectly on the pillion seat. It is available in the color Grand Prix Red R-380 and gives your motorcycle a particularly sporty look. The seat cover is made of high-quality materials and impresses with its first-class workmanship.A small comfort cushion provides additional seating comfort and also allows longer rides without any problems. The seat cover is easy to fit and can be combined with the aluminum cover Art. No.: 08F76MKND50 to further enhance the sporty look.So if you are looking for a high-quality and stylish accessory for your Honda CBR650R, then the original Grand Prix Red R-380 pillion cover is the perfect choice for you.
High windshield (Smoke) tinted for Honda CBR 650R (Bj.19-) Original
With this windshield, you not only get a great look, but also improved airflow on your bike. The dark smoke design gives your bike a cool look and protects you from direct sunlight and wind at the same time. The high windshield is specially designed for your motorcycle model and fits perfectly on your Honda CB650R (Bj.19-). The high-quality material and precise workmanship ensure a long service life and easy installation. With this original Honda product, you can be sure that you are getting a high-quality windshield that is perfectly matched to your motorcycle.
High windshield (Clear) clear for Honda CB650R (Bj.19-)
This windshield is specially made for your Honda CB650R (Bj.19-) and offers you optimal protection from wind and weather. The high design changes the airflow and you can ride relaxed even at higher speeds. The clear design ensures an unrestricted view of the road and can be easily integrated into the design of your Honda CB650R. Installation is quick and easy, so you can put the windshield on right out of the box. Thanks to the high-quality materials and precise workmanship, the High Windshield (Clear) clear for Honda CB650R (Bj.19-) is particularly durable and robust. You will enjoy this product for a long time and bring your riding experience to a new level.
Alurack top case carrier black for Honda CBR 650 R (19-20) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Alurack adapter plate for mounting Hepco & Becker top cases or soft luggage (not suitable for top cases with universal plastic plate). Hepco & Becker aluminum racks are specially designed for Hepco & Becker top cases. As the successor to the tried and tested tubular luggage racks, the Alurack is seen as a logical further development and is offered for the younger generation of motorcycles. Each Alurack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Alurack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. Details: Solid construction No additional adapters are required for top case mounting High-quality surface finish Recommended payload: 5 kg payload in the top case (please observe vehicle-specific information, the stored installation instructions and motorcycle manufacturer information) Technically almost identical to the Easyrack top case carrier, except that the bracket for holding the top case is fixed at the top and cannot be folded down The model-specific base carrier is the same for the Easyrack and Alurack A special bracket is required to mount the aluminum standard top case 35 (article number: 700007350 or 700007351) Luggage carriers do not require an ABE or registration Recommended top speed: 130 km/h Weight: 2.8 kg Scope of delivery: Model-specific Alurack top case carrier + mounting kit + mounting instructions Notes: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag Developed for the standard condition of the machine. Not tested with accessories such as: exhaust, license plate holder or other indicators
ARROW Auspuff X-KONE für Honda CB650R / CBR650R 2019-, Edelstahl (Nur mit ARROW Krümmer)
ARROW Auspuff X-KONE für Honda CB650R / CBR650R 2019-, Edelstahl (Nur mit ARROW Krümmer) ARROW X-KONE Endschalldämpfer mit Edelstahl-Hülle und Carbon-Endkappe, mit dB-Killer, mit Straßenzulassung. Für Honda CB650R, Typ RH02, Modelljahr 2019- CBR650R, Typ RH01, Modelljahr 2019- Montage nur in Verbindung mit ARROW-Krümmer AR-71704 Produktkennzeichnung: Abgastechnik ARROW Hinweis: Montage nur mit ARROW-Krümmer: AR-71704KZ = mit Katalysator und Straßenzulassung AR-71704MI = ohne Katalysator. Straßenzulassung entfällt! Produkt Typ: ARROW X-KONE Auspuff Honda CB650R 19- Edelstahl
BMC Sport air filter FM832/04 for Honda CBR 650 R (RC74, RC96) (RH01, RH07)
The BMC standard air filters are made of the best materials and guarantee a much higher air flow than conventional paper filters. In the production of the performance-optimized filters, the extensive know-how from racing is used and each individual meets the highest requirements. For example, the frame of the filters cannot break, the filtering, reusable cotton fabric is impregnated with a special oil and the aluminum mesh is resistant to gasoline vapors and oxidation thanks to treatment with an epoxy solution. Why choose BMC? Better than OEM filters Better than synthetic filters Better than other cotton filters Highest quality Rigorous testing procedures ecological and economical Winner in all categories BMC operates in numerous sectors: automotive, racing, aerospace, marine and industrial, always following the specific regulations and requirements of each of the mentioned industries. Accordingly, BMC tests extremely rigorously and accurately to ensure that its air filters are of the highest possible quality. The technical solutions applied by BMC are derived from the results of continuous and intensive laboratory tests. BMC performs filtration tests according to the international standards for air filters (ISO 5011). According to these tests, BMC air filters have a 98.5 percent filtration efficiency.BMC's filter frame design is manufactured using a unique process called "full molding." This allows the striking red filter to be produced in a single molding process without having to glue the corners, which would cause breakage. On the BMC air filter protrudes the least rubber material of all filters available on the market (less than 6 mm), allowing maximum filter surface.Have a look at our YouVideo:
BMC Sportluftfilter für Honda CB650R 2019-
BMC Sportluftfilter für Honda CB650R 2019- BMC Sportluftfilter für Honda CB650R / Neo Sports Cafe, (ab Modelljahr '19-) CBR650R (ab Modelljahr '19-) Produktkennzeichnung: BMC Luftfilter Produkt Typ: BMC Sportluftfilter für Honda CB650R
C-Bow side carrier black for Honda CBR 650 R (19-20) Hepco & Becker
The C-Bow side bag holder is designed to hold a variety of Hepco & Becker bags. Softbags for sporty, dynamic motorcycles and saddlebags for choppers and cruisers can be attached to the motorcycle with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorcycle and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions. Features: Solid side carrier for mounting Hepco & Becker C-Bow side bags and panniers High-quality surface finish Normal Hepco & Becker hard cases such as the Junior or Journey do not fit! Krauser K-Wing cases do not fit on the C-Bow carrier! Recommended payload: 5 kg per bag/case (please observe the fitting instructions, vehicle-specific information and motorcycle manufacturer's specifications for any restrictions that may apply) Can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier) Luggage rack extensions can restrict bag mounting on the carrier Luggage carriers do not require an ABE or registration in the papers Weight: 2.4 kg Color: black Scope of delivery: Left, right, mounting material and instructions Notes: Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.
Easyrack top case carrier black for Honda CBR 650 R (19-20) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Easyrack adapter plate for mounting Hepco & Becker top cases or soft luggage (not suitable for top cases with universal plastic plate). Each Easyrack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Easyrack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. Details: Solid basic construction made of steel and an aluminum carrier plate No additional adapters are required for top case mounting High-quality surface finish Technically almost identical to the Alurack top case carrier, except that the bracket for top case mounting can be folded in when not in use and the Alurack bracket stands rigidly upwards The model-specific base carrier is the same for the Easyrack and Alurack Luggage carriers do not require an ABE or registration Recommended payload: 5 kg payload (please observe model-specific information, the stored installation instructions and motorcycle manufacturer information) Recommended maximum speed: 130 km/h Weight: 2.8 kg Scope of delivery: Model-specific Easyrack Topcaseträger + mounting kit + mounting instructions Notes: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag. Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators.
Factory Links wheel bearing set
Bearing set for front wheel FACTORY LINKS bearings are packed with a heavy-duty premium marine grease and an additive of a special complex thickener that allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep out any moisture, we've gone from a 30% grease fill to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specifically designed for off-road use, unlike industrial 2RS ball bearings which offer low torque resistance and therefore low resistance to water ingress.
Gilles clutch lever FXL for Honda
Optimal shape for all grip styles Unique due to protected GILLES.TOOLING design Ideal handle length for perfect control Phosphated, precise bearing Road legal through ABE Adjustable up to 35 positions Grip width adjustment accurate to the millimeter Conveniently adjustable by central adjusting wheel Predetermined breaking point in the 2-finger area
HiFlo air filter element for Honda CB 650 R / CBR 650 R (19-20)
HIFLO air filters are produced from the highest quality materials to give modern high performance engines the best performance: Maximum filtration and perfect airflow !
HIGHSIDER pro blinker adapter For original indicators, For license plate holder, For Honda
With this black aluminum blinker adapter, the original indicators can be used on our HIGHSIDER or HIGHSIDER pro license plate holders. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Scope of delivery: 1 pair
HIGHSIDER pro turn signal adapter black For original turn signals, For license plate holder, For Honda (pair)
Turn signal adapter for HIGHSIDER AKRON and HIGHSIDER pro MANTIS license plate holderWith these turn signal adapters, the original LED turn signals can still be used on the license plate holder.Oblong hole approx. 16x32mmScope of delivery: 1 pair
HIGHSIDER pro handlebar weights black M6 Honda (pair)
HIGHSIDER handlebar weights for 1 inch handlebar end mirrors for Honda Black anodized aluminium handlebar weights for various Honda original handlebars. All our handlebar end mirrors (hanging mirrors) with a diameter of 1 inch (25.4 mm) can be mounted on these handlebar weights. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Please check the dimensions for accuracy of fit before purchasing! Dimensions:Total width: approx. 41 mmWidth outside the handlebars: 28 mmScrew length: 56 mm, M6Diameter: 25.4 mmWeight: pair approx. 140g
