Short license plate holder incl. license plate light for Yamaha YZF-R7 (21-)
Article number:
280-408HP
Manufacturer:
Highsider
Description
Product information
The HIGHSIDER license plate holder AKRON-RS adapts perfectly to the lines of your bike through its design.
The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating.
This ensures an optimal fit and durability.
The stepless adjustment allows you to bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal holders of the AKRON-RS are adjustable in width and thus suitable for any type of accessory turn signals. This adjustability allows you to adjust the position for your turn signals to the most different license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem.
To screw the license plate securely and reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific mount
- infinitely adjustable turn signal holder
- slotted turn signal mount for easy installation without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable angle of inclination
- additional screw for optimal position security
- easy fixation without further work steps (e.g. drilling)
- easy mounting of the license plate through slotted holes
The scope of delivery of the AKRON-RS includes
- Model-related holder with mounting parts
- AKRON-RS license plate holder
- Adjustable turn signal brackets
- E-tested reflector with adjustable holder
- Mounting instructions
Notes:
- A special turn signal holder is optionally available for the original turn signals in the accessories tab.
- If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.
Tips:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To avoid damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. Precise cutting is done by laser. After edging, the plate is given a weather-resistant black powder coating.
This ensures an optimal fit and durability.
The stepless adjustment allows you to bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal holders of the AKRON-RS are adjustable in width and thus suitable for any type of accessory turn signals. This adjustability allows you to adjust the position for your turn signals to the most different license plates. To allow the installation of the turn signals without separation from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of EU license plates is therefore no problem.
To screw the license plate securely and reduce vibrations, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific mount
- infinitely adjustable turn signal holder
- slotted turn signal mount for easy installation without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable angle of inclination
- additional screw for optimal position security
- easy fixation without further work steps (e.g. drilling)
- easy mounting of the license plate through slotted holes
The scope of delivery of the AKRON-RS includes
- Model-related holder with mounting parts
- AKRON-RS license plate holder
- Adjustable turn signal brackets
- E-tested reflector with adjustable holder
- Mounting instructions
Notes:
- A special turn signal holder is optionally available for the original turn signals in the accessories tab.
- If there are side reflectors mounted on your original license plate holder, they must be reattached in a suitable position or replaced with new ones.
Tips:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
| Fitment: | Fitment assured |
|---|
Manufacturer
Highsider
|
Paaschburg & Wunderlich GmbH |
Reviews 0
Login
No reviews found. Share your insights with others.