CB 600 F Hornet 1998-2002 (PC34/PC36)
Available categories
Matching articles
alpha Technik Drosselkit 25 kW für Honda CB600F Hornet, PC34
alpha Technik Drosselkit 25 kW für Honda CB600F Hornet, PC34 Gutachten 25 kW für Honda CB600F Hornet, Fzg.Typ: PC34, ab Modelljahr 1998 mit ABE-Nr. K016 Ausf.A und ab Modelljahr 2000 mit EG-BE-Nr. e13*92/61*0020*, mit Umbauteilen Produktkennzeichnung: Leistungsänderung 25 kW Geänderte Fahrzeugteile: Ansaugblenden Produkt Typ: Drosselkit 25 kW für Honda CB600F Hornet, PC34 Lieferumfang: TÜV Gutachten und Drosselteile für Leistungsreduzierung auf 25 kW (mit 2 vorgedruckten Typenschildaufkleber)
alpha Technik Gabelwellendichtring Satz 41x54x11
alpha Technik Gabelwellendichtring Satz 41x54x11 ARI Simmerringsatz, Gabelwellendichtringe 41x54x11, mit Doppelfeder Produktkennzeichnung: Fahrwerkstechnik Produkt Typ: Gabelwellendichtring Satz 41x54x11
ATHENA valve cover gasket
ATHENA is one of the world's best-known manufacturers of cylinder-piston sets for 2- and 4-stroke engines. The high-performance components from this manufacturer improve engine performance while maintaining its reliability.Rocker arm cover gasket setFor a high-quality overhaulThe gaskets must always be replaced every time the engine is overhauledSupplied without screw gaskets
Blinker front left/ rear right for: HONDA CB600F HORNET '98-02
Dimensions and properties identical to standard component.
Blinker, front right / rear left for: HONDA CB600F HORNET '98-02
Dimensions and properties identical to standard component.
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Engine guard chrome for Honda CB 600 F Hornet (98-06) /S (98-02) Hepco & Becker
Whether you spend most of your time on rough terrain, on country roads or in the city, a crash bar from Hepco & Becker is always the right choice. Your motorcycle is always effectively protected against unexpected mishaps. More than that: in the event of a fall or unintentional contact with the ground, you can protect the motorcycle and the rider from major damage. The protective bars from Hepco & Becker perfectly trace the lines of the machine and thus give the motorcycle an individual character. Made from an extremely stable tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad. Exclusive look thanks to high-quality surface finish: high-quality powder coating from Germany.On top, motorcycle protective bars are incredibly well suited for securely lashing your machine to a trailer if you ever need to transport it. Features: Material: Tubular steel made in Germany Surface finish: Elegant, high-gloss chrome Effectively protects in the event of minor accidents or mishaps Helpful when lashing the motorcycle Comprehensive and easy-to-understand assembly instructions Crash bars are registration-free - so they do not need to be entered in the papers and therefore do not require an ABE Weight: 2.8 kg Color: Chrome, high-gloss silver Scope of delivery: Right + left incl. mounting material (spacers, sleeves, washers etc.) and Installation instructions Notes: Please observe the model-specific information listed in the installation instructions and the properties! Unless explicitly stated otherwise, Hepco & Becker model-specific products have only been developed for the standard condition of the motorcycle! For safety reasons, all protection bars should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions.
HIGHSIDER pro 45 mm headlight Dual-Stream LED black E-approved (1pc)
HIGHSIDER DUAL-STREAM LED headlight, black, E-approved The small all-in-one ellipsoid headlight with round lens is a powerful LED main headlight in a black housing and robust bracket. The special feature of the HIGHSIDER DUAL-STREAM is the parking light illuminated ring around the ellipsoid lens and the shutter technology with which a mechanical shutter switches between high and low beam. By using this modern LED technology, the smallest possible housing dimensions can be achieved with the greatest possible light output. Our highlights - give your bike an unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series make it a highlight in any case! Dimensions:Lens diameter: approx. 45 mmHeight: 70.2 mmWidth: 67 mmDepth: 96.5 mmDistance between mounting holes: 67 mmLateral mounting holes: M 5 mmHousing material: aluminumWeight: 0.230 kg Power consumption:12V / 12W, 739.3 lm, low beam12V / 19 W, 739.3 lm, high beam Connections:Position light = brownLow beam = whiteThe white cable is connected to ignition plus (+) High beam = blueGround = green (-)
HIGHSIDER pro 5 3/4 inch headlight insert type 10 LED E-approved (1pc)
HIGHSIDER 5 3/4 inch LED main headlight insert TYPE 10 with parking light, E-approved Dimensions:Diameter A = 145 mmDiameter GA = 132 mmDiameter I = 125 mmT = 60 mmR = 10 mmCable length: 210 mm Weight: 658 gConnections: (3 pin plug) Red = low beam (+) Yellow = high beam (+) White = position light (+) Brown = earth (-)Scope of delivery: 1 piece
HIGHSIDER pro 7 inch headlight insert type 11 LED black E-approved (1pc)
HIGHSIDER TYPE 11 7-inch LED main headlight insert, E-approved High beam, low beam, parking light and with TFL (daytime running light) function The reflector emits an asymmetrical luminous flux - only approved for right-hand traffic See and be seen! This is extremely important for motorcyclists. On many motorcycles, the H4 or H7 lamp lights up, more or less twinkling away. Seeing better usually also means being seen better, which is not unimportant as summer turns to fall and in times when cars are increasingly equipped with bright daytime running lights. Whether as a replacement for better visibility at night, better visibility during the day or to give your motorcycle a more attractive appearance, if you are looking for a stylish and innovative power headlight, then the LED main headlight is an excellent choice. The built-in LED daytime running light in TYPE 11 is the perfect way to improve visibility during the day. The ellipsoid lenses in combination with powerful LEDs turn night into day and thus combine a strong plus in safety with a polarizingly unique look. Sensational - give your bike your unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series will definitely make you a highlight! Dimensions: A diameter = 170 mm GA Diameter = 165 mm I diameter = 160 mm T = 60 mm R = 9 mm Total depth from glass to cooling fins: 96 mm Cable length: 170 mm Connections: Power input: 3 pin connector Black cable = ground (-) White cable = low beam (+) Blue cable = high beam (+) TFL: Black cable = earth (-) Brown cable = daytime running light (+) Gray cable = parking light (+) Scope of delivery: 1 piece
HIGHSIDER pro 7 inch headlight insert type 3 LED black E-approved
HIGHSIDER LED main headlight insert TYPE 3 This round, chrome-plated reflector with black or chrome-plated cover has a high beam, low beam and parking light function and emits an asymmetrical luminous flux that is only approved for right-hand traffic, E-approved. Our highlights - give your bike your unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series will definitely turn your bike into a highlight! Dimensions: Diameter A = 177 mm Diameter GA = 168 mm Diameter I = 160 mm T = 61 mm R = 10 mm Connections: Black cable = earth (-) Red cable = low beam (+), power consumption: at 12 volts 18 watts approx. 1132 lumens. White cable = high beam (+), power consumption: at 12 volts 30 watts approx. 1770 lumens. Brown cable = parking light (+), power consumption: at 12 volts 0.7 watts Scope of delivery: 1 piece Notes: Asymmetrical use, only approved for right-hand traffic.
HIGHSIDER pro 7 inch headlight insert type 3 LED black E-approved
HIGHSIDER LED main headlight insert TYPE 3 This round, chrome-plated reflector with black or chrome-plated cover has a high beam, low beam and parking light function and emits an asymmetrical luminous flux that is only approved for right-hand traffic, E-approved. Our highlights - give your bike your unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series will definitely turn your bike into a highlight! Dimensions: Diameter A = 177 mm Diameter GA = 168 mm Diameter I = 160 mm T = 61 mm R = 10 mm Connections: Black cable = earth (-) Red cable = low beam (+), power consumption: at 12 volts 18 watts approx. 1132 lumens. White cable = high beam (+), power consumption: at 12 volts 30 watts approx. 1770 lumens. Brown cable = parking light (+), power consumption: at 12 volts 0.7 watts Scope of delivery: 1 piece Notes: Asymmetrical use, only approved for right-hand traffic.
HIGHSIDER pro 7 inch headlight insert type 4 LED E-approved (1pc)
This round, chrome-plated reflector with clear glass has a high beam, low beam, parking light and daytime running light function. The daytime running light and position light are installed in a central strip, creating a very attractive light pattern - the low beam shines above the strip, while the high beam shines below it. The reflector emits an asymmetrical luminous flux - only approved for right-hand traffic - and is E-approved. Our highlights - give your bike your unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series will definitely turn your bike into a highlight! Dimensions: Diameter A = 177 mm Diameter GA = 168 mm Diameter I = 160 mm T = 61 mm R = 10 mm Connections: Black cable = earth (-) Blue cable = low beam (+), power consumption at 12V: 1.8A, 22W Yellow cable = high beam (+), power consumption at 12V: 1.3A, 13W Black cable = ground (-) TFL: Black cable = ground (-) Red cable = daytime running light (+), power consumption at 12V: 1.2A, 14W White cable = position light (+), power consumption at 12V: 0.2A, 2.4W Scope of delivery: 1 piece Note 1: - Asymmetrical use, only approved for right-hand traffic. - The enclosed 3-pin standard plug must be fitted by the customer after the reflector has been installed. View of plug contacts: High beam (yellow) = right Low beam (blue) = top Ground (black) = left Note 2: The daytime running light can also be used on vehicles without a light switch. This requires the following components, for example: Switch: Art. No. 240-044 HIGHSIDER DRL CONTROL- BOX CB1 : Art. No. 208-108 (switches between low beam and daytime running light)
HIGHSIDER pro 7 inch headlight insert type 8 LED black E-approved (1pc)
HIGHSIDER LED headlight insert TYPE 8- See and be seen! -Of the utmost importance for motorcyclists. The built-in LED daytime running light with position light in TYPE 8 is the perfect way to improve visibility during the day. The correct daytime running light circuit on the vehicle is provided without additional control boxes or switches, complies with regulations and simplifies installation. Modern LED lighting technology has made huge progress in the headlight sector. An LED bend lighting headlight for retrofitting to motorcycles heralds the next evolutionary stage in vehicle lighting. The HIGHSIDER LED headlamp with bend lighting offers clear advantages over a conventional headlamp. The static cornering light activates an additional light when the motorcycle is tilted in a bend. Thanks to the improved illumination, you can see more of the bend and what is behind it. The rider can adjust better to the conditions and situations and is safer on the road. Two ellipsoid lenses in combination with powerful LEDs turn night into day and thus combine a strong plus in safety with a polarizing, unique look. The headlight is available in black with tinted glass or in chrome with clear glass. The HIGHSIDER LED headlamp with daytime running light, position light and cornering light is of course E-approved. To switch from daytime running light to dipped beam: Press the high beam/flasher button briefly (approx. 1 second) and release the button as soon as the dipped beam is active. The low beam is then permanently active. Sensational - give your bike your unmistakable style! The unusual design and perfect technology of the HIGHSIDER headlight series will definitely make you a highlight!Dimensions:Diameter A = 177.8 mmDiameter GA = 169 mmDiameter I = 166.5 mmT = 59 mmR = 10 mmTotal depth from glass to cooling fins: 99.10 mmConnections:Power input: 3-pin plugRed cable = low beam (+)White cable = high beam (+)Black cable = earth (-)Separate cable (round plug):Red cable = LED position light (+)Scope of delivery: 1 pieceNotes:The resistor included in the scope of delivery is designed for the R nineT (2014), but may also be suitable for other vehicle models. This resistor prevents the parking light error message.This headlight does NOT work in conjunction with the HIGHSIDER E-BOX TYPE 1 (item number: 208-200)
HIGHSIDER pro Akron grip rubber black 7/8 inch (22.2 mm), 132 mm
HIGHSIDER AKRON handlebar grip rubber, black with aluminum ring in various colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create a new kind of design language with the overlapping of the two aluminum sleeves. The outer one embodies timeless design with its lines and its trapezoidal tongues form a beautiful contrast to the bead-blasted black aluminum cylinder underneath. The HIGHSIDER lettering is incorporated into the handle structure. The removable end caps allow the mounting of handlebar end indicators, handlebar end mirrors or handlebar weights. The grips give your bike the elegant HIGHSIDER look and enhance its appearance. Our accessory tip: Excellent in combination with the visually coordinated design handlebar weights from our own company. The handlebar ends pick up on the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions:Suitable for 7/8 inch (22 mm) Length: 132 mm Outer diameter rubber: approx. 34 mm Outer diameter aluminum sleeve: approx. 37 mm Scope of delivery: 1 pair
HIGHSIDER pro Akron Grip Rubber Titanium 7/8 inch (22.2 mm), 132 mm
HIGHSIDER AKRON handlebar grip rubber, black with aluminum ring in various colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create a new kind of design language with the overlapping of the two aluminum sleeves. The outer one embodies timeless design with its lines and its trapezoidal tongues form a beautiful contrast to the bead-blasted black aluminum cylinder underneath. The HIGHSIDER lettering is incorporated into the handle structure. The removable end caps allow the mounting of handlebar end indicators, handlebar end mirrors or handlebar weights. The grips give your bike the elegant HIGHSIDER look and enhance its appearance. Our accessory tip: Excellent in combination with the visually coordinated design handlebar weights from our own company. The handlebar ends pick up on the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions:Suitable for 7/8 inch (22 mm) Length: 132 mm Outer diameter rubber: approx. 34 mm Outer diameter aluminum sleeve: approx. 37 mm Scope of delivery: 1 pair
HIGHSIDER pro Akron-LS handlebar weights
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.
HIGHSIDER pro Akron-LS handlebar weights red (pair)
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely coordinated - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.
HIGHSIDER pro Akron-LS handlebar weights titanium (pair)
HIGHSIDER AKRON-LS handlebar weights, black with cap in various colors - Styling for your bike - With these elegantly designed handlebar ends with handlebar end mirror mount, you can design your bike in detail according to your ideas. These end pieces serve as mounts for all HIGHSIDER & SHIN YO handlebar end mirrors with external handlebar clamps. Handlebar ends also serve to reduce annoying vibrations on the handlebars. Thanks to the clamping system with various sleeves, universally suitable for 7/8 (Ø22 mm), 1 inch (Ø25.4 mm) or X-Bar (Ø28.6 mm) tubular handlebars with an inner diameter of 12 to 22 mm. Our accessory tip: Excellent in combination with the visually coordinated AKRON designer handlebar grips from our own company. The caps of the handlebar ends mirror the design of the grip rubbers and turn your motorcycle cockpit into an eye-catcher. If you do want to switch back to handlebar mirrors, you can use the optionally available color rings instead of a handlebar end mirror in just a few simple steps and thus set additional color accents. The color rings are simply slid over the handlebar end and fastened with the grub screw on the ring. Precisely coordinated - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes.Dimensions:Handlebar weight Ø: 37.4 mm Width: 29 mm Mounting for mirror: Ø 29.90 mm, width: 12 mm Scope of delivery: 1 pair incl. 2 clamping sleeves each with D. 12 mm and D. 16 mm 2 spacer sleeves each with D. 14 mm, D. 18 mm and D. 21 mm 2 x M6 central bolts 2 x M6 conical nuts NOTE: For handlebar ends with clamping system, the ends of the handlebars must not be blocked by threaded inserts or similar. Handlebar ends do not have to be approved and therefore do not require any test marks, certificates or ABEs.