NC 750 S 2014-2015 (RC70)
Available categories
Matching articles
Alurack top case carrier black for Honda NC 700 S (12-13) /750 S/DCT (14-20) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Alurack adapter plate for mounting Hepco&Becker top cases or soft luggage (not suitable for top cases with universal plastic plate). Hepco&Becker aluminum racks are specially designed for Hepco&Becker top cases. As the successor to the tried and tested tubular luggage racks, the Alurack is seen as a logical further development and is offered for the younger generation of motorcycles. Each Alurack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Alurack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. Details: Solid construction No additional adapters are required for top case mounting High-quality surface finish Recommended payload: 5 kg payload in the top case (please observe vehicle-specific information, the stored installation instructions and motorcycle manufacturer information) Technically almost identical to the Easyrack top case carrier, except that the bracket for holding the top case is fixed at the top and cannot be folded down The model-specific base carrier is the same for the Easyrack and Alurack A special bracket is required to mount the aluminum standard top case 35 (article number: 700007350 or 700007351) Luggage carriers do not require an ABE or registration Recommended maximum speed: 130 km/h Weight: 4.1 kg Scope of delivery: Model-specific Alurack top case carrier + mounting kit + mounting instructions Notes: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag. Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators.
BMC Sportluftfilter für Honda CTX 700 2014-2016; NC 700 2012-; NC 750 2014-; NJ NM4 70 Vultus 2015-2
BMC Sportluftfilter für Honda CTX 700 2014-2016; NC 700 2012-; NC 750 2014-; NJ NM4 70 Vultus 2015-2017 BMC Sportluftfilter für Honda CTX 700 A/D/N/NA/ND (Modelljahr 2014-2016) NC 700 Integra/S/SA/SD/XAC/XC/XDC (Modelljahr 2012-2014) NC 750 Integra/SA/SD/XA/XD (Modelljahr 2014-) Produktkennzeichnung: BMC Luftfilter Produkt Typ: BMC Sportluftfilter für Honda CTX/NC 700/750
C-Bow side carrier black for Honda NC 700 S (12-13) /750 S/DCT (14-20) Hepco & Becker
The C-Bow side bag holder is designed to hold a variety of Hepco & Becker bags. Softbags for sporty, dynamic motorcycles and saddlebags for choppers and cruisers can be attached to the motorcycle with the C-Bow holder. Its elegant, unobtrusive design blends in perfectly with the overall lines of the vehicle. Naturally, it keeps the saddlebags safely away from the hot exhaust silencer. Thanks to modern C-Bow technology, the matching bags can be attached to the C-Bow simply and easily with just one click and locked to prevent theft. The bags are securely fastened to the motorcycle and remain in position even when loaded. On many models, the indicators remain in their original position. Further information can be found in the fitting instructions. Features: Solid side carrier for mounting Hepco & Becker C-Bow side bags and panniers High-quality surface finish Normal Hepco & Becker hard cases such as the Junior or Journey do not fit! Krauser K-Wing cases do not fit on the C-Bow carrier! Recommended payload: 5 kg per bag/case (please observe the fitting instructions, vehicle-specific information and motorcycle manufacturer's specifications for any restrictions that may apply) Can usually be combined with top case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific information for the respective carrier) Luggage rack extensions can restrict bag mounting on the carrier Luggage carriers do not require an ABE or registration in the papers Weight: 2.4 kg Color: black Scope of delivery: Left, right, mounting material and instructions Notes: Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Crash bar for Honda NC700 / NC750 (Bj.12-) Givi
for Honda NC700S/X (Bj.12-13) / NC750S/X (Bj.14-15) / NC750S/X DCT (Bj.14-15) / NC750S (Bj.16-) / Honda NC750X (Bj.16-)Specific crash bar / Tube diameter 25 mm / We recommend that the installation is carried out by a professional mechanicSuitable for the following models: Honda NC700S/X (12-13)/ NC750S/X / NC750S/X DCT (14-15) / NC750S (16-18) / Honda NC750X (16-19)Important note:GIVI products are designed for vehicles in original condition. Compatibility with accessories from other manufacturers such as exhaust systems etc. cannot be guaranteed
Easyrack top case carrier black for Honda NC 700 S (12-13) /750 S/DCT (14-20) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Easyrack adapter plate for mounting Hepco&Becker top cases or soft luggage (not suitable for top cases with universal plastic plate). Each Easyrack top case carrier is developed specifically for each model and therefore blends in harmoniously with the overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Easyrack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. Details: Solid basic construction made of steel and an aluminum carrier plate No additional adapters are required for top case mounting High-quality surface finish Technically almost identical to the Alurack top case carrier, except that the bracket for top case mounting can be folded in when not in use and the Alurack bracket stands rigidly upwards The model-specific base carrier is the same for the Easyrack and Alurack Luggage carriers do not require an ABE or registration Recommended payload: 5 kg payload (please observe model-specific information, the stored installation instructions and motorcycle manufacturer information) Recommended maximum speed: 130 km/h Weight: 4.2 kg Color: black Scope of delivery: Model-specific Easyrack Topcaseträger + mounting kit + mounting instructions Notes: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag. Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators.
Engine guard black for Honda NC 700 S (12-13) /750 S/DCT (14-20) Hepco & Becker
Whether you spend most of your time on rough terrain, on country roads or in the city, a crash bar from Hepco & Becker is always the right choice. Your motorcycle is always effectively protected against unexpected mishaps. More than that: in the event of a fall or unintentional contact with the ground, you can protect the motorcycle and the rider from major damage. The Hepco & Becker mudguards perfectly trace the lines of the machine, giving the motorcycle an individual character. Made from an extremely sturdy tube-in-tube construction, manufactured from German quality steel or stainless steel, they offer maximum protection - with many newer models already featuring an integrated crash pad. Exclusive look thanks to high-quality surface finish: high-quality powder coating from Germany.On top of that, motorcycle protection bars are incredibly well suited to securely lashing your bike to a trailer if you ever need to transport it. Features: Material: Tubular steel made in Germany Surface finish: High-quality powder coating Effectively protects in the event of minor accidents or mishaps Helpful when lashing the motorcycle Comprehensive and easy-to-understand assembly instructions Crash bars are registration-free - so they do not need to be entered in the papers and therefore do not require an ABE Weight: 3.7 kg Color: black Scope of delivery: Right, left incl. mounting material (spacers, sleeves, washers etc.) and Installation instructions Notes: Please observe the model-specific information listed in the installation instructions and properties! Unless explicitly stated otherwise, Hepco & Becker model-specific products have only been developed for the standard condition of the motorcycle! For safety reasons, all protection bars should be adequately checked after a crash and replaced if necessary. If original or accessory parts have already been fitted, there may be restrictions; these can be found in the fitting instructions.
Foot extension for the side stand for Honda Givi
for Honda CB 500 X (Bj.13-) / NC700S/X (Bj.12-13) / NC750S/X (Bj.14-15) / NC750S/X DCT (Bj.14-15) / Integra 700 (Bj.12-13) / XL 700V Transalp (Bj.08-13) / Integra 750 (Bj.14-15) / NX750X (Bj.16-)Specific foot extension made of aluminum and stainless steel for the original side standImportant note:GIVI products were developed for vehicles in their original condition. Compatibility with accessories from other manufacturers such as exhaust systems etc. cannot be guaranteed
Foot widening for the side stand for Honda Givi
for Honda CB 500 X (Bj.13-) / NC700S/X (Bj.12-13) / NC750S/X (Bj.14-15) / NC750S/X DCT (Bj.14-15) / Integra 700 (Bj.12-13) / XL 700V Transalp (Bj.08-13) / Integra 750 (Bj.14-15) / NX750X (Bj.16-)Specific foot widening made of aluminum and stainless steel for the original side standImportant note:GIVI products are designed for vehicles in original condition. Compatibility with accessories from other manufacturers such as exhaust systems, etc. can not be guaranteed
Front protection bar black for Honda NC 700 S (12-13) /750 S/DCT (14-20) Hepco & Becker
Details: Good protective effect in the event of accidents and falls at low speeds Turn signals, clutch and brake levers, exhaust silencers, fairing parts etc. are effectively protected High-quality powder coating Incl. mounting material Weight: 2.3 kg
Gas cap decor with HRC logo original for all Honda models
- Carbon look- HRC logo
HIGHSIDER pro distance bar black set 25mm
Handlebar spacers for Ø 22.2 mm handlebar diameters available in various colors and heights.Easy to raise the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamp.Delivery includes the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!There are different requirements and conditions for each vehicle that allow the conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the vehicle's standard handlebars.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer cables or cables) due to a different shape of the handlebar.Raising the original handlebar can also lead to additional modifications to the vehicle.Check whether the following requirements apply to your vehicle (-see ABE):- use permitted when using a compensation pad for the fork bridge- use permitted with 20 mm longer brake line- use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!
HIGHSIDER pro distance block silver set 25mm
Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights.Simple increase of the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamp.Delivery includes the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!There are different requirements and conditions for each vehicle that allow the conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the vehicle's standard handlebars.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer cables or cables) due to a different shape of the handlebar.Raising the original handlebar can also lead to additional modifications to the vehicle.Check whether the following requirements apply to your vehicle (-see ABE):- use permitted when using a compensation pad for the fork bridge- use permitted with 20 mm longer brake line- use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!
HIGHSIDER pro Outdoor Cover Black Moto / Scooter - S (1pc)
HIGHSIDER tarpaulinThe perfect outdoor protection for two-wheelers: High-quality tarpaulin made from elastic, tear-resistant, waterproof and UV-resistant high-tech fiber. With rubberized seams, the hard-wearing motorcycle cover offers the best protection against rain, dew or other moisture. The extremely robust cover has a soft inner fleece and is therefore particularly gentle on the paintwork, even with daily use. Designed for road motorcycles, it meets the highest requirements of two-wheeled riders, not least due to the integrated ventilation openings, heat protection on both sides and reinforced lock eyelet for anti-theft protection. It is attached to the motorcycle with an adjustable click fastener. High-contrast, white HIGHSIDER lettering on the long sides of the black tarpaulin and the white HIGHSIDER logo on the back visually emphasize this premium product. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Determine the correct size of your cover by measuring the length, width and height of your motorcycle/scooter and comparing them with the dimensions given. Dimensions:Size S:Length: 183 cmWidth: 80 cm Height: 115 cmFits most 50 cc scooters.Size M:Length: 203 cmWidth: 80 cm Height: 120 cmFits most light motorcycles (80/125 cc and supersports/superbikes).Size L:Length: 229 cmWidth: 89 cm Height: 125 cmFits most naked bikes.Size XL:Length: 246 cmWidth: 94 cm Height: 130 cmFits most choppers and small touring bikes.Size XXL:Length: 264 cmWidth: 105 cm Height: 135 cmSuitable for large cruisers and touring bikes.Scope of delivery: 1 piece incl. practical carrying bag DETERMINE SIZE:Determine the correct size of your tarpaulin by measuring the length, width and height of your motorcycle/scooter or take the dimensions from the vehicle registration document to compare the specified dimensions. The correct size is a tarpaulin that is about 5-10 cm longer than the length of the motorcycle and about 5 cm above the ground. TIP:Don't buy too big, the more it flaps, the more it rubs. And in winter, a tarpaulin always tears and breaks exactly where it can move around. Make sure there is enough space: a gap of at least five centimetres to the ground increases the chance of air exchange and counteracts condensation. If you are in doubt between two sizes, choose the larger option. NOTE:In the case of STRETCH COVERING tarpaulins, it is recommended to choose a size smaller than normal tarpaulins without stretch properties.
HIGHSIDER pro Street Bar L00 Handlebar Black 7/8 inch
HIGHSIDER pro steel handlebars 7/8 inch (22.2mm)HIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own selection of material and material treatment as well as the production quality of the handlebars, which has been optimized over decades. In its own test series in the 1990s, HIGHSIDER pro researched the load on handlebars during riding and designed its own handlebars to withstand the actual load. The result is a product made of high-strength steel that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly checks its handlebars with its own test program, which ensures the consistent quality of the handlebars.The HIGHSIDER pro steel handlebars have an outer diameter of 22.2mm (7/8 inch) and a wall thickness of 2mm (18mm inside). The surface is high-gloss polished and chrome-plated or black KTL-coated.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings. We recommend using the HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The range of models is huge and is expanded every year with new entries.The ABE reliably documents which handlebar type fits and is approved on the motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Therefore, see the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid- and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro Superbike A01 handlebar aluminum black, 7/8 inch
7/8 inch (22.2mm) aluminum handlebars from HIGHSIDER proHIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own choice of material and material treatment as well as the production quality of the handlebars, which has been optimized over decades. In the 1990s, HIGHSIDER pro worked out the perfect alloy, heat treatment and processing method in its own series of tests. The result is a product that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly tests its handlebars using a specially developed in-house test program, which ensures the high quality of the handlebars.HIGHSIDER pro aluminium handlebars have an outer diameter of 22.2 mm and a wall thickness of 4 mm (14 mm inside). The surface is highly polished and available in up to six anodized colors, depending on the handlebar type. Handlebars in black are also available in matt bead blasted.The handlebars are supplied without drill holes for the anti-rotation lock of the switch fittings.In order to adopt the position of the drill holes from the standard handlebars in the best possible way, we recommend using a HIGHSIDER pro drilling template.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro Superbike A01 handlebars black bead blasted, aluminum, 7/8 inch
7/8 inch (22.2mm) aluminum handlebars from HIGHSIDER proHIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own choice of material and material treatment as well as the production quality of the handlebars, which has been optimized over decades. In the 1990s, HIGHSIDER pro worked out the perfect alloy, heat treatment and processing method in its own series of tests. The result is a product that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly tests its handlebars using a specially developed in-house test program, which ensures the high quality of the handlebars.HIGHSIDER pro aluminium handlebars have an outer diameter of 22.2 mm and a wall thickness of 4 mm (14 mm inside). The surface is highly polished and available in up to six anodized colors, depending on the handlebar type. Handlebars in black are also available in matt bead blasted.The handlebars are supplied without drill holes for the anti-rotation lock of the switch fittings.In order to adopt the position of the drill holes from the standard handlebars in the best possible way, we recommend using a HIGHSIDER pro drilling template.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro Superbike AN1 handlebar black bead blasted, aluminum, 7/8 inch
7/8 inch (22.2mm) aluminum handlebars from HIGHSIDER proHIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own choice of material and material treatment as well as the manufacturing quality of the handlebars, which has been optimized over decades. In the 1990s, HIGHSIDER pro developed the perfect alloy, heat treatment and processing method in its own series of tests. The result is a product that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly tests its handlebars using a specially developed in-house test program, which ensures the high quality of the handlebars.HIGHSIDER pro aluminium handlebars have an outer diameter of 22.2mm and a wall thickness of 4mm (14mm inside). The surface is highly polished and available in up to six anodized colors, depending on the handlebar type. Handlebars in black are also available in matt bead blasted.The handlebars are supplied without drill holes for the anti-rotation lock of the switch fittings.In order to adopt the position of the drill holes from the standard handlebars in the best possible way, we recommend using a HIGHSIDER pro drilling template.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.