Motorcycle tarpaulin green/black Original Kawasaki
Superstretch material. Reinforced underside. Available in green and red.
Helmet lock for Kawasaki Eliminator 500 (24-) Original
Helmet lock for screwing on. The lock can be mounted so that it fits onto the existing ignition key. (One-Key system)
Radiator guard for Kawasaki Eliminator 500 (24-) Original
The black radiator shroud protects your radiator from dirt on the road with a robust metal guard. The elegant laser-cut pattern offers maximum airflow with minimum weight.
Design seat for Kawasaki Eliminator 500 (24-) Original
Driver's seat in 2-pattern design with decorative stitching at the same seat height as the standard seat. (accessory for Eliminator 500, standard equipment for Eliminator 500 SE)
High seat (+30mm) for Kawasaki Eliminator 500 (24-) Original
30 mm higher seat, which increases the seat height from 735 mm to a total of 765 mm. This increases seating comfort and allows taller riders to adopt a more relaxed leg position.
Low seat (-20mm) for Kawasaki Eliminator 500 (24-) Original
20 mm lower seat, which lowers the seat height from 735 mm to 715 mm. This seat also has a narrower front section. This increases control and gives smaller riders a better reach to the ground.
Relay kit USB socket Original Kawasaki
Required for mounting the USB-C socket.
USB-C socket for Kawasaki Eliminator 500 (24-) Original
Waterproof USB-C socket that is conveniently attached to the handlebars. Vibration-damped. The socket can be closed with a cap. Maximum total power is 3A. (Relay kit must be installed for operation) (sold separately)
Crash pads for Kawasaki Eliminator 500 (24-) Original
Elegant crash pads with aluminum insert and Kawasaki logo. Provide additional protection for the bodywork. Can be fitted quickly and easily without any modifications to the motorcycle.
Tank pad for Kawasaki Eliminator 500 (24-) Original
Black foil tank pad with Kawasaki logo for better protection against scratches.
Passenger grab handle for Kawasaki Eliminator 500 (24-) Original
Offer your passenger additional comfort with this classic style passenger grab rail Made of black coated steel. Included in the type approval of the motorcycle. (Cannot be combined with the accessory luggage carrier)
Luggage rack for Kawasaki Eliminator 500 (24-) Original
Robust black luggage rack made of tubular steel, which is securely attached to the rear chassis Dimensions of the luggage rack approx. 20cm x 25cm (8" x 10") With 4 pins for easy attachment of straps and hooks.(Cannot be combined with the accessory grab handle)
Alurack top case carrier for Kawasaki Eliminator 500 (24-) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Alurack adapter plate for mounting Hepco & Becker top cases or soft luggage (not suitable for top cases with universal plastic plate) Each Alurack top case carrier is developed specifically for each model and therefore blends in with the harmonious overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Alurack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. solid basic construction made of steel and an aluminum carrier plate Scope of delivery: model-specific Alurack top case carrier + mounting kit + mounting instructions no additional adapters are required for top case mounting high-quality surface finish technically, it works almost the same as the Easyrack top case carrier, except that the bracket for the top case mount is fixed at the top and cannot be folded down the model-specific base carrier is the same for the Easyrack and Alurack a special bracket is required instead of the normal Alurack bracket to mount the Hepco & Becker Alu Standard Topcase 35 (article number: 700007350 or 700007351) Luggage racks do not require ABE or registration Recommended payload: 5kg payload (please observe model-specific information, the stored assembly instructions and motorcycle manufacturer information) Note: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag. Recommended maximum speed: 130 km/h Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators.
Arrow Slip-On sports exhaust for Kawasaki Eliminator 500 (24-)
Arrow matt black slip-on exhaust with carbon heat shield and carbon end cap. This system is lighter than the standard exhaust system and produces a deep, sporty sound. This exhaust system is homologated in accordance with EU regulations (emissions and noise) and has ECE type approval. (Euro 5+)
C-Bow side carrier for Kawasaki Eliminator 500 (24-) Hepco & Becker
solid side carrier for mounting Hepco & Becker C-Bow side bags and panniers high-quality surface finish normal Hepco & Becker hard-shell cases such as the Junior or Journey do not fit! Krauser K-Wing cases do not fit on the C-Bow carrier! Recommended payload: 5kg per bag/case (please observe the fitting instructions, vehicle-specific information and motorcycle manufacturer's specifications for any restrictions that may apply) can usually be combined with top-case carriers, sissy bars or solo racks without any problems (please observe the installation instructions or the vehicle-specific instructions for the respective carrier) Luggage rack extensions can restrict bag mounting on the carrier Luggage racks do not require an ABE or registration in the papers Scope of delivery: left + right + mounting instructions + mounting kit Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators. Make sure that the bags always have sufficient distance to the exhaust and that the indicators have a sufficient beam angle. The exhaust jet must not be directed at the bags.
Easyrack top case carrier for Kawasaki Eliminator 500 (24-) Hepco & Becker
Top case carrier consisting of a model-specific mounting kit and the Easyrack adapter plate for mounting Hepco & Becker top cases or soft luggage (not suitable for top cases with universal plastic plate) Each Easyrack top case carrier is developed specifically for each model and therefore blends into the harmonious overall appearance of the motorcycle. Thanks to the production from high-quality aluminum in combination with a steel base carrier, the Easyrack has a high strength and a very elegant appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. solid basic construction made of steel and an aluminum carrier plate Scope of delivery: model-specific Easyrack top case carrier + mounting kit + mounting instructions no additional adapters are required for top case mounting high-quality surface finish technically almost the same as the Alurack top case carrier, except that the bracket for the top case holder can be folded in when not in use and the Alurack bracket stands rigidly upwards the model-specific base carrier is the same for the Easyrack and Alurack Luggage carriers do not require an ABE or registration Recommended payload: 5kg payload (please observe model-specific information, the stored installation instructions and motorcycle manufacturer information) Note: Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag. Recommended maximum speed: 130 km/h Developed for the standard condition of the machine. Not tested with accessories such as exhaust, license plate holder or other indicators.
Rider backrest for Kawasaki Eliminator 500 (24-) Hepco & Becker
ATTENTION: Can only be mounted in combination with Solorack (see accessories)!
HIGHSIDER Pro Apollo Bullet LED turn signal housing black / lens smoke gray (pair), front & rear
HIGHSIDER APOLLO BULLET LED indicators, for front and rear E-approved. Power LED blinker in a black aluminum housing with tinted glass. With this innovative lighting technology, 2 very bright SMD LEDs are installed in the center, enabling an extremely small design. The outer ring, on the other hand, consists of the new COB technology (Chip On Board). The new LED chip embedding for high-performance LEDs achieves a very high luminance with the best possible efficiency and service life. This also enables higher light values to be achieved than with conventional LEDs. In the right direction - with the innovative blinker series from HIGHSIDER. Show not only where you want to go, but also who you are. This is trend-setting design at its best. Dimensions:A: 22 mmB: 34 mmD: 40 mm Threaded bolt M8 x 17 mm Connections:Black cable = ground (-)Yellow cable = blinker (+) Scope of delivery: 1 pair Note: E-approved for front and rear. Can be ordered as an option:HIGHSIDER Rear light/indicator APOLLO BULLET, article no. 254-171HIGHSIDER Indicator/position light APOLLO BULLET, article no. 204-173
HIGHSIDER pro Apollo Bullet LED turn signal/position light black/tinted 2in1, E-approved (pair)
HIGHSIDER APOLLO BULLET 2in1 LED indicator/position light, for front E-approvedLED indicator/position light in a black aluminum housing with tinted glass. With this innovative lighting technology, 2 very bright SMD LEDs are installed in the center, enabling an extremely small design. The outer ring, on the other hand, consists of the new COB technology (Chip On Board). The new LED chip embedding for high-performance LEDs achieves a very high luminance with the best possible efficiency and service life. This also enables higher light values to be achieved than with conventional LEDs.In the right direction - with the innovative blinker series from HIGHSIDER. Show not only where you want to go, but also who you are. This is trend-setting design at its best.Installation location: FrontDimensions:A: 22 mmB: 34 mmD: 40 mmThreaded bolt M8 x 17 mmConnections:Black cable = ground (-)Yellow cable = blinker (+)White cable = parking light (+)Scope of delivery: 1 pair
HIGHSIDER pro distance bar black set 35mm
Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights.Simple increase of the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamp.Delivery includes the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!There are different requirements and conditions for each vehicle that allow the conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the vehicle's standard handlebars.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer cables or cables) due to a different shape of the handlebar.Raising the original handlebar can also lead to additional modifications to the vehicle.Check whether the following requirements apply to your vehicle (-see ABE):- use permitted when using a compensation pad for the fork bridge- use permitted with 20 mm longer brake line- use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!
HIGHSIDER pro distance bar silver set 35mm
Handlebar spacers for Ø 22.2mm handlebar diameter available in various colors and heights.Simple increase of the seat position, CNC-milled from high-quality aluminum, are installed in the standard handlebar clamp.Delivery includes the required longer screws.ATTENTION IMPORTANT NOTE:Please check before the conversion whether the vehicle intended for the conversion is listed in the ABE attached here!There are different requirements and conditions for each vehicle that allow the conversion of the clamping blocks.The model assignments of the HIGHSIDER pro clamping blocks listed in the ABE are tested for use with the vehicle's standard handlebars.The additional use of a HIGHSIDER pro accessory handlebar is possible, but may require additional modifications to the vehicle (longer cables or cables) due to a different shape of the handlebar.Raising the original handlebar can also lead to additional modifications to the vehicle.Check whether the following requirements apply to your vehicle (-see ABE):- use permitted when using a compensation pad for the fork bridge- use permitted with 20 mm longer brake line- use permitted with 30 mm longer brake lineFailure to comply will invalidate the operating license for the vehicle!
HIGHSIDER pro Esagano-RS grip rubber black 7/8 inch (22.2 mm), 125 mm (pair)
HIGHSIDER ESAGANO-RS handlebar grip rubber, black with aluminum ring in black Steep and flat trapezoids form the basic shape of the aluminum CNC-machined grip sleeves of the HIGHSIDER ESAGANO-RS grips and create a futuristic design that symbolizes the design language of modern motorcycles. The striking grip sleeve is complemented by our new ergonomic grip rubber and its modern topographical design. Together they ensure a convincing grippy result both in terms of handling and appearance and are suitable for 7/8 inch handlebars. The raised collar of the grip sleeve ensures a more homogeneous transition to the handlebar fittings and also conveys this haptically to your hands. You can close off the open end of the handlebars with the enclosed plain black caps. If you are looking for a more confident finish with a harmonious design, we offer you an attractive alternative with the handlebar ends from the ESAGANO series or from our comprehensive HIGHSIDER product range, which will complete your bike to perfection and skillfully set the scene. Dimensions: Suitable for 7/8 inch (22.2 mm) Length: 125 mm Outer diameter rubber approx: Ø32 mm Outer diameter of aluminum sleeve: approx. Ø40 mm Inner diameter rubber 1 approx: Ø20 mm Inner diameter rubber 2 approx: Ø23 mm Scope of delivery: 1 pair of handlebar grip rubber
