GSX-S 1000 GT 2022- (EK12AZ)
Available categories
Matching articles
Axle protector front for Suzuki GSX-S 1000 S/GT (Bj.19-) Original Suzuki
for Suzuki GSX-S 1000 S Katana (Bj.19-) Front axle protector, aluminum and nylon, silver with black contrast and Suzuki logo.Set consists of two pieces.WVTA homologation.
BMC sports air filter for Suzuki DL 1050 V-Strom DE (20-)
The BMC standard air filters are made from the best materials and guarantee a much higher air flow rate than conventional paper filters. The comprehensive know-how from racing is used in the production of the performance-optimized filters and each one meets the highest requirements. For example, the frame of the filters cannot break, the filtering, reusable cotton fabric is impregnated with a special oil and the aluminum mesh is resistant to gasoline vapors and oxidation thanks to treatment with an epoxy solution. Why choose BMC? Better than OEM filters Better than synthetic filters Better than other cotton filters Highest quality Rigorous testing procedures Ecological and economical Winner in all categories BMC is active in numerous sectors: Automotive, racing, aviation, marine and industrial, always in accordance with the specific regulations and requirements of each of these sectors. Accordingly, BMC tests extremely rigorously and accurately to ensure that its air filters are of the highest possible quality. The technical solutions applied by BMC are derived from the results of continuous and intensive laboratory testing. BMC carries out filtration tests in accordance with the international standards for air filters (ISO 5011). BMC air filters have a filtration efficiency of 98.5 percent.BMC's filter frame construction is manufactured in a unique process called "full molding". This allows the striking red filter to be produced in a single molding process without the need to glue the corners, which would cause breakage. Of all the filters available on the market, the BMC air filter has the least overhanging rubber material (less than 6 mm), thus maximizing the filter surface area.Take a look at our YouVideo:
Brake lever for Suzuki GSX-S 1000 GT (21-) Original
Anodized aluminum brake lever with GSX-S logo.
Brembo brake caliper in red set front for Suzuki GSX-S 1000 GT (21-) Original
Replacement brake caliper in red. Attention: without brake pads and mounting parts(Original mounting parts must be used)
Clutch lever for Suzuki GSX-S 1000 GT (21-) Original
Anodized aluminum clutch lever with GSX-S logo.
Comfort seat set for Suzuki GSX-S 1000 GX / GT (24-) Original
Elegant look and maximum comfort: double-layer upholstery construction made of two layers of urethane foam with different thicknesses. Surface remains 14% cooler in sunlight compared to the standard seat The set consists of comfort rider seat and comfort pillion seatSuitable for Suzuki GSX-S 1000 GX and GT (24-)
Crash bar for Aprilia Tuareg 660 (21-) SW Motech
Suitable for the Aprilia Tuareg 660, the crash bars are made of tubular steel with weather- and corrosion-resistant powder coating in black. The surface finish is applied in a state-of-the-art facility at the SW-MOTECH plant in Brno, Czech Republic. Crash bars from SW-MOTECH provide the necessary extra safety for the tank, fairing and components. The elements, which are manufactured specifically for the motorcycle type, fit seamlessly into the look of the vehicle while offering optimum lean angle clearance. Tailor-made mounting elements allow a resilient and simple installation at original mounting points. Construction from robust steel Weather- and corrosion-resistant powder coating in black Reliable protection of important components Extremely sturdy construction matches the appearance of the motorcycle Model-specific development guarantees precise fit and resilient frame connection Optimum lean angle clearance guaranteed Easy installation by screwing to factory frame mounting points Scope of delivery 2 x crash bars Fitting instructions Mounting material Details Material: steel Surface: powder coated Color: black Total weight: approx. 4.8 kg
Easyrack topcas carrier for Suzuki GSX-S 1000 GT (22-)
Each Easyrack Topcaseträger is developed model-specific and thus fits into the harmonious overall appearance of the motorcycle. Thanks to the production of high-quality aluminum in combination with a steel base carrier, the Easyrack has a high strength, as well as a very noble appearance. Additional attachment points for luggage straps, for example to attach luggage rolls, are integrated into the design of the rack. solid basic construction made of steel and an aluminum carrier plate Scope of delivery: model-specific Easyrack Topcaseträger + mounting kit + installation instructions there are no further adapters for topcase mounting needed high quality surface finish works technically almost the same as the Alurack topcase carrier, except that the bracket for topcase mounting can be folded when not in use and the Alurack bracket is rigid upwards the model-specific base carrier is the same for Easyrack and Alurack Luggage carriers do not require ABE or registration Recommended load: 5kg load (please note the model-specific instructions, the installation instructions and the motorcycle manufacturer's specifications) Note: Heavy luggage should generally not be transported in the top case, but in the side panniers or tank bag. Recommended maximum speed: 130 km/h Designed for stock condition of the machine. Not tested with accessories such as: exhaust, license plate holder or other indicators.
Electrosport controller
The alternator stators and regulators from Electrosport enable reliable replacement of the standard component.
Factory Links steering head bearing kit TM EN125/250/300
ContainsDust Seals x2, Tapered Roller x2Steering Stem Bearing Service Kits Full Service Steering Stem OEM quality Set OEM type tapered roller bearings NBR Race Dust Seals
Front fender carbon for Suzuki GSX-S 1000 GT (21-) Original
Replacement fender made of carbon, Matt.
Handlebar ends for Suzuki GSX-S1000 original
Handlebar end weights in noble design and made of high quality aluminum, silver / black with Suzuki logo
HiFlo air filter element for Suzuki GSX-S 1000 / GT (15-)
HIFLO air filters are produced from the highest quality materials to give modern high performance engines the best performance: Maximum filtration and perfect airflow !
HIGHSIDER pro blinker adapter black original, for license plate holder, Suzuki (pair)
Turn signal adapter for HIGHSIDER AKRON and HIGHSIDER pro MANTIS license plate holderThese turn signal adapters allow the original LED turn signals to continue to be used on the license plate holder. Scope of delivery: 1 pair
HIGHSIDER pro Outdoor Cover Black Moto / Scooter - S (1pc)
HIGHSIDER tarpaulinThe perfect outdoor protection for two-wheelers: High-quality tarpaulin made from elastic, tear-resistant, waterproof and UV-resistant high-tech fiber. With rubberized seams, the hard-wearing motorcycle cover offers the best protection against rain, dew or other moisture. The extremely robust cover has a soft inner fleece and is therefore particularly gentle on the paintwork, even with daily use. Designed for road motorcycles, it meets the highest requirements of two-wheeled riders, not least due to the integrated ventilation openings, heat protection on both sides and reinforced lock eyelet for anti-theft protection. It is attached to the motorcycle with an adjustable click fastener. High-contrast, white HIGHSIDER lettering on the long sides of the black tarpaulin and the white HIGHSIDER logo on the back visually emphasize this premium product. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Determine the correct size of your cover by measuring the length, width and height of your motorcycle/scooter and comparing them with the dimensions given. Dimensions:Size S:Length: 183 cmWidth: 80 cm Height: 115 cmFits most 50 cc scooters.Size M:Length: 203 cmWidth: 80 cm Height: 120 cmFits most light motorcycles (80/125 cc and supersports/superbikes).Size L:Length: 229 cmWidth: 89 cm Height: 125 cmFits most naked bikes.Size XL:Length: 246 cmWidth: 94 cm Height: 130 cmFits most choppers and small touring bikes.Size XXL:Length: 264 cmWidth: 105 cm Height: 135 cmSuitable for large cruisers and touring bikes.Scope of delivery: 1 piece incl. practical carrying bag DETERMINE SIZE:Determine the correct size of your tarpaulin by measuring the length, width and height of your motorcycle/scooter or take the dimensions from the vehicle registration document to compare the specified dimensions. The correct size is a tarpaulin that is about 5-10 cm longer than the length of the motorcycle and about 5 cm above the ground. TIP:Don't buy too big, the more it flaps, the more it rubs. And in winter, a tarpaulin always tears and breaks exactly where it can move around. Make sure there is enough space: a gap of at least five centimetres to the ground increases the chance of air exchange and counteracts condensation. If you are in doubt between two sizes, choose the larger option. NOTE:In the case of STRETCH COVERING tarpaulins, it is recommended to choose a size smaller than normal tarpaulins without stretch properties.
HIGHSIDER pro X-Bar Adventure X04 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Cross Bar X00 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike Flat XN1 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Black Bead-Shallow, Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.