Speed Triple 1050 2005-2010 (515NJ)
Available categories
Matching articles
Blinker front left / rear right for: YAMAHA YZF125R '08-10
Dimensions and properties identical to standard component.
Blinker front right / rear left for: YAMAHA YZF125R '08-10
Dimensions and properties identical to standard component.
Electrosport controller
The alternator stators and regulators from Electrosport enable reliable replacement of the standard component.
Electrosport regulator ESR535
The ESR535 is a high quality regulator/rectifier specifically designed to replace the unreliable OEM part on several Triumph models. Our ESR535 has a very efficient heat sink that keeps the temperature of the unit low. Internally we use only the best quality components for the power circuits. The result is a very high quality unit that is far superior to the OEM regulator. This regulator/rectifier precisely controls the output power and ensures a stable charge of the battery over the entire speed range. Like all regulators/rectifiers and stators manufactured by ElectroSport, this unit comes with a full one-year warranty. -Block connector B 4-way, 2 x green, 2 x red
Electrosport stator
*** ESG753 for ENG no. 183487 >*** NOT ALL 1050s use the same stator. Check your OEM stator before purchase. If your OEM stator has an outer diameter of 114 mm, buy ESG753. If your OEM stator only has an outer diameter of 104 mm, buy ESG794 ESG753 is a very high quality stator that replaces the OEM stator in Triumph 1050 Speed Triple models between 2005 and 2011 with ENG No. 183487. ElectroSport manufactures the ESG753 stator using a high quality core and the highest quality copper wire for the windings. A slightly different winding configuration compared to stock and the high magnetic conductivity of the new stator core result in significantly improved efficiency compared to stock. As a result, our ESG753 stator offers perfect performance over the entire speed range and also runs much cooler than the standard stator, which drastically improves reliability. We install very high quality connection cables with heat and chafe resistant insulation as well as high quality rubber seals and insulation coatings, making this stator a plug-in replacement for the OEM unit. Like all stators manufactured by ElectroSport, this ESG753 comes with a one-year warranty.
Factory Links wheel bearing set
FACTORY LINKS bearings are packed with a heavy duty premium marine grease and an addition of a special complex thickeners which allows it to be virtually waterproof. It provides unsurpassed rust and corrosion protection. Also to keep any moisture out, we have gone from 30% grease filling to a 60% for harsh conditions. Our FACTORY LINKS ball bearings are specially developed for an Off-Road use, unlike Industrial 2RS type ball bearings offer low torque resistance and hence weak resistance to water intrusion.
Gas tank cap BIHR original type for: APRILIA PEGASO 650 i.e
Bihr fuel filler capStandard component type - identical to the standard componentEnables the cover to be replaced without modifications
HIGHSIDER pro Conero Type 2 handlebar weights black (pair)
Available in glossy black with polished bevels or in matt black - BLACK EDITION - The handlebar end weights are made of CNC-milled aluminum. The HIGHSIDER CONERO TYPE 2 is supplied with a special adapter (black aluminum ring), which makes it possible to mount our HIGHSIDER handlebar end mirrors with a Ø 30 mm mount. Universally suitable for handlebars with an inner diameter of 12 to 22 mm Ø, suitable for most 7/8 inch and 1 inch aluminum or steel handlebars Our HIGHSIDER CONERO series is characterized by a minimalist design and fits perfectly with uncovered motorcycles. The beautifully shaped and high-quality aluminum add-on parts give your roadster a face and character. The HIGHSIDER CONERO series takes you back to the time when a motorcycle was simply allowed to be a motorcycle - reduced for riding, experiencing and learning. Tailor-made for your motorcycle - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions: Diameter: approx. 34.5 mm Length: 17 mm Diameter of mirror mount: 30 mm Specifications: Weight bar end weights with mounting: 132 g Color: Glossy black with polished bevels or matt black Material: Aluminum Please check the dimensions for accuracy of fit before purchasing! Scope of delivery: 2 x bar end weights. 2 x clamping sleeves D. 12 mm and D. 16 mm. 2 x centering sleeves type 1, type 2, type 3. 2 x black coated M6 central screw and M6 conical nut.
HIGHSIDER pro Conero Type 2 handlebar weights black (pair)
Available in glossy black with polished bevels or in matt black - BLACK EDITION - The handlebar end weights are made of CNC-milled aluminum. The HIGHSIDER CONERO TYPE 2 is supplied with a special adapter (black aluminum ring), which makes it possible to mount our HIGHSIDER handlebar end mirrors with a Ø 30 mm mount. Universally suitable for handlebars with an inner diameter of 12 to 22 mm Ø, suitable for most 7/8 inch and 1 inch aluminum or steel handlebars Our HIGHSIDER CONERO series is characterized by a minimalist design and fits perfectly with uncovered motorcycles. The beautifully shaped and high-quality aluminum add-on parts give your roadster a face and character. The HIGHSIDER CONERO series takes you back to the time when a motorcycle was simply allowed to be a motorcycle - reduced for riding, experiencing and learning. Tailor-made for your motorcycle - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. Dimensions: Diameter: approx. 34.5 mm Length: 17 mm Diameter of mirror mount: 30 mm Specifications: Weight bar end weights with mounting: 132 g Color: Glossy black with polished bevels or matt black Material: Aluminum Please check the dimensions for accuracy of fit before purchasing! Scope of delivery: 2 x bar end weights. 2 x clamping sleeves D. 12 mm and D. 16 mm. 2 x centering sleeves type 1, type 2, type 3. 2 x black coated M6 central screw and M6 conical nut.
HIGHSIDER pro Dot handlebar weights black (pair)
HIGHSIDER handlebar weights DOT, chrome-plated or blackHandlebar weights made of chrome-plated or black aluminum with chrome-plated or black central screw. Universal fit for handlebars with an inner diameter of 12 to 22 mm - i.e. for most 7/8 inch and 1 inch aluminum or steel handlebars. All HIGHSIDER and SHIN YO hanging handlebar end mirrors with external clamps can be attached to the handlebar weights.Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike according to your wishes. DimensionsHandlebar weight: Diameter: 35.5 mmWidth: 17 mmMirror mount:Diameter: 29.8 mmWidth: 12 mmWeight with mounting parts: 74 gThread M6 x 1.25 mmPlease check the dimensions for accuracy of fit before purchasing!Scope of delivery: 1 pair: 2 x handlebar weights each.2 x clamping sleeves D. 12 mm and D. 16 mm each.2 x centering sleeves type 1, type 2, type 3 each.2 x central bolt M6, lock washer and cone nut M6 each.Note:Spare mounting kit: 161-034
HIGHSIDER pro Evo handlebar weights
HIGHSIDER EVO bar ends, chrome-plated or black. Chrome-plated or black bar ends, suitable for handlebars with an inner diameter of 12 to 22 mm - i.e. for most 7/8 inch and 1 inch aluminum or steel handlebars. All our bar end mirrors (hanging mirrors) with a diameter of 1 inch (25.4 mm) can be attached to the Bar End Weights. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your bike. With the highest level of quality and functionality, you can easily customize your bike to your liking. Dimensions: Diameter: 35.5 mm Length: 28 mm Specifications: Material: Aluminum Please check the dimensions for accuracy of fit before purchasing! Scope of delivery: 1 set, including mounting set and universal clamping system: 2 x bar end weights. 2 x clamping sleeves D. 12 mm and D. 16 mm. 2 x centering sleeves type 1, type 2, type 3. 2 x central screw M6, toothed washer and conical nut M6. Note: Spare mounting kit: 1107882 (161-034)
HIGHSIDER pro Outdoor Cover Black Moto / Scooter - S (1pc)
HIGHSIDER tarpaulinThe perfect outdoor protection for two-wheelers: High-quality tarpaulin made from elastic, tear-resistant, waterproof and UV-resistant high-tech fiber. With rubberized seams, the hard-wearing motorcycle cover offers the best protection against rain, dew or other moisture. The extremely robust cover has a soft inner fleece and is therefore particularly gentle on the paintwork, even with daily use. Designed for road motorcycles, it meets the highest requirements of two-wheeled riders, not least due to the integrated ventilation openings, heat protection on both sides and reinforced lock eyelet for anti-theft protection. It is attached to the motorcycle with an adjustable click fastener. High-contrast, white HIGHSIDER lettering on the long sides of the black tarpaulin and the white HIGHSIDER logo on the back visually emphasize this premium product. Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle. With the highest level of quality and functionality, you can easily customize your bike to your liking. Determine the correct size of your cover by measuring the length, width and height of your motorcycle/scooter and comparing them with the dimensions given. Dimensions:Size S:Length: 183 cmWidth: 80 cm Height: 115 cmFits most 50 cc scooters.Size M:Length: 203 cmWidth: 80 cm Height: 120 cmFits most light motorcycles (80/125 cc and supersports/superbikes).Size L:Length: 229 cmWidth: 89 cm Height: 125 cmFits most naked bikes.Size XL:Length: 246 cmWidth: 94 cm Height: 130 cmFits most choppers and small touring bikes.Size XXL:Length: 264 cmWidth: 105 cm Height: 135 cmSuitable for large cruisers and touring bikes.Scope of delivery: 1 piece incl. practical carrying bag DETERMINE SIZE:Determine the correct size of your tarpaulin by measuring the length, width and height of your motorcycle/scooter or take the dimensions from the vehicle registration document to compare the specified dimensions. The correct size is a tarpaulin that is about 5-10 cm longer than the length of the motorcycle and about 5 cm above the ground. TIP:Don't buy too big, the more it flaps, the more it rubs. And in winter, a tarpaulin always tears and breaks exactly where it can move around. Make sure there is enough space: a gap of at least five centimetres to the ground increases the chance of air exchange and counteracts condensation. If you are in doubt between two sizes, choose the larger option. NOTE:In the case of STRETCH COVERING tarpaulins, it is recommended to choose a size smaller than normal tarpaulins without stretch properties.
HIGHSIDER pro Superbike A01 handlebar aluminum black, 7/8 inch
7/8 inch (22.2mm) aluminum handlebars from HIGHSIDER proHIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own choice of material and material treatment as well as the production quality of the handlebars, which has been optimized over decades. In the 1990s, HIGHSIDER pro worked out the perfect alloy, heat treatment and processing method in its own series of tests. The result is a product that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly tests its handlebars using a specially developed in-house test program, which ensures the high quality of the handlebars.HIGHSIDER pro aluminium handlebars have an outer diameter of 22.2 mm and a wall thickness of 4 mm (14 mm inside). The surface is highly polished and available in up to six anodized colors, depending on the handlebar type. Handlebars in black are also available in matt bead blasted.The handlebars are supplied without drill holes for the anti-rotation lock of the switch fittings.In order to adopt the position of the drill holes from the standard handlebars in the best possible way, we recommend using a HIGHSIDER pro drilling template.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro Superbike A01 handlebars black bead blasted, aluminum, 7/8 inch
7/8 inch (22.2mm) aluminum handlebars from HIGHSIDER proHIGHSIDER pro stands for outstanding handlebar quality. This is due to the company's own choice of material and material treatment as well as the production quality of the handlebars, which has been optimized over decades. In the 1990s, HIGHSIDER pro worked out the perfect alloy, heat treatment and processing method in its own series of tests. The result is a product that combines extremely high bending stiffness with resistance to breakage. To confirm the consistent quality, HIGHSIDER pro regularly tests its handlebars using a specially developed in-house test program, which ensures the high quality of the handlebars.HIGHSIDER pro aluminium handlebars have an outer diameter of 22.2 mm and a wall thickness of 4 mm (14 mm inside). The surface is highly polished and available in up to six anodized colors, depending on the handlebar type. Handlebars in black are also available in matt bead blasted.The handlebars are supplied without drill holes for the anti-rotation lock of the switch fittings.In order to adopt the position of the drill holes from the standard handlebars in the best possible way, we recommend using a HIGHSIDER pro drilling template.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never use in direct sunlight and do not allow the cleaner to dry out.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Cross Bar X00 handlebar aluminum black, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Black Bead-Shallow, Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER pro X-Bar Superbike X01 Handlebar Silver Aluminum, 1 1/8 inch
X-Bar aluminium handlebars from HIGHSIDER pro - 28.6mm Ø in the clamping area / 22.2mm Ø in the grip areaHIGHSIDER pro stands for outstanding handlebar quality.This is due to the company's own selection of materials and material treatment as well as the production quality of the handlebars, which has been optimized over decades. The X-Bar handlebars impress with twice the bending stiffness of standard handlebars.The basis for this exceptional stability of the handlebars is the large diameter in the clamping area and the even, conical transition to the grip area.The handlebars bounce less and offer more reserves under extreme loads.The diameter of the handlebars is 28.6 mm in the clamping area and tapers to 22.2 mm towards the grip tube.The wall thickness of the handlebar ends is 4 mm (inner Ø 14 mm). The surface is matt bead-blasted or high-gloss polished and available in up to four anodized colors, depending on the handlebar type.We also offer a version with carbon fibre coating.As is already known in the high-tech bicycle sector, HIGHSIDER pro now also offers a version of the X-Bar handlebar with genuine carbon fibre coating. The aluminum tube is covered with a carbon fiber tube. This sandwich construction achieves a further reduction in weight with the same handlebar stiffness. The production is absolute precision work. This is the only way to comply with the required tolerances of a motorcycle handlebar. Great care must be taken when fitting these handlebars to ensure that the transparent top layer of the carbon fiber material is not damaged.The handlebars are supplied without holes for the anti-rotation protection of the switch fittings.We recommend using a HIGHSIDER pro drilling template to ensure that the position of the holes is as close as possible to the standard handlebars.All HIGHSIDER pro handlebars are supplied with ABE.The model range is huge and is expanded every year with new entries.In the ABE you will find reliable documentation of which handlebar type fits and is approved for your motorcycle.As a rule, the assignments in the ABE are without conditions.However, there are also exceptions.For example, HIGHSIDER pro offers handlebar mounts for many models, with which you can also mount one of the X-Bar handlebars on a motorcycle with a standard 22.2 mm mount.Please refer to the entry for your motorcycle in the ABE.If you cannot find your vehicle in the ABE, the ABE can be used as an accompanying document for an individual approval.Scope of delivery: 1 pieceCare instructions:- Only use acid and alkali-free cleaner on all handlebars and their surface variants!- Never clean in direct sunlight and do not allow the cleaner to dry.- Avoid contact with brake fluid, brake cleaner, oil, fuel, polishing pastes with abrasive particles, etc., and wipe up any dripping immediately with a soft cloth.- Test the compatibility of cleaning agents on an inconspicuous area before use!- No guarantee or warranty in the event of improper cleaning and care.
HIGHSIDER Smart switch for brake light, front, Suzuki (1pc)
HIGHSIDER smart brake light switch for various models.It can happen that the original contact switch for brake light control on your motorcycle gives up the ghost and you need a new brake light switch. In this case, you can get a new switch from our range. For the front or rear. These spare parts are of OEM quality and are said to be extremely durable. The replacement is done in no time at all and your driving safety is restored. Scope of delivery: 1 piece
HIGHSIDER smart Type BC 420 Repair Brake Lever Black With ABE (1pc)
It doesn't always have to be the original. Our HIGHSIDER smart brake levers replace the original 1 to 1. Precisely manufactured from high-quality aluminum, they meet all requirements. Therefore also with ABE. If you are also looking for the right clutch lever, you are sure to find it in our bike finder.
HIGHSIDER smart Type BC 420 Repair Brake Lever Silver With ABE, adjustable (1pc)
It doesn't always have to be the original. Our HIGHSIDER smart brake levers replace the original 1 to 1. Precisely manufactured from high-quality aluminum, they meet all requirements. Therefore also with ABE. If you are also looking for the right clutch lever, you are sure to find it in our bike finder.
HIGHSIDER smart Type BC 420 Repair brake lever silver/black With ABE, adjustable (1pc)
It doesn't always have to be the original. Our HIGHSIDER smart brake levers replace the original 1 to 1. Precisely manufactured from high-quality aluminum, they meet all requirements. Therefore also with ABE. If you are also looking for the right clutch lever, you are sure to find it in our bike finder.